Panasonic Panafax UF-895, Service Manual

Page: 156 / 342

Panasonic UF-885 / 895
156
044 REDIAL COUNT 0 = no redial
~
15 = 15 times Selects the redial count from 0 to 15 times in 1 step
intervals.
045 RING DETECT COUNT 1 = 1 ring
~
9 = 9 rings Selects the ring detection count from 1 to 9 rings in
1 ring step intervals.
046 ON-HOOK TIME 0 = 0 sec.
~
90 = 90 sec. Selects the on-hook time between sequential
communication calls in 1 second step intervals.
047 RESPONSE WAIT 1 = 1 sec.
~
90 = 90 sec. Selects the waiting interval for the response after
completing the dialing.
048
049 Not used
050 RING DETECT MODE 1 = Normal
2 = Rough Selects the quality of ringer detection. Use if the
line signal is out of regulation, set to "Rough" so
that the unit may detect the ringing signals.
051 INTERNATIONAL DT MODE
(For Belgium, France and
Spain version only.) 1 = Off
2 = On Selects whether to distinguish the 4-digit
international access code prefix.
052 PULSE RATE 1 = 10 pps
2 = 20 pps Selects the dial pulse rate 10/20 pps.
053
054 Not used
055 BUSY TONE CHECK 1 = Off
2 = On Selects whether to detect the Busy Tone.
056 DIAL TONE CHECK
(Except for USA and Canada
version) 1 = Off
2 = On Selects whether to detect dial tone before dialing
the telephone number.
057 DC LOOP CHECK
(Except for USA and Canada
version) 1 = Off (will not check)
2 = On (checks) Selects whether the unit checks the DC Loop
during communication.
058 COMM.JRNL +IMAGE 1 = Off (without image)
2 = On (with image) Selects whether the machine prints the COMM.
Journal with image.
059 CONFIDENTIAL RCV
REPORT 1 = Off (does not print out)
2 = On (prints out) Selects whether the machine prints the
CONFIDENTIAL RCV REPORT.
060 VERSION Indicates the ROM version.
061 TX/RX//PRT/CPY COUNTER TX/RX/PRT/CPY Displays the transmitted, received, total printed and
copied document count.
062 PRINT COUNTER 1 = Off
2 = On Selects whether to print in the Fax Parameter List,
the counter information that is displayed in the
Function Parameter No. 61.
063
~
069
Not used
070 LINE ERROR 1 = 128 lines
2 = 256 lines
3 = 512 lines
4 = 1024 lines
5 = 2048 lines
6 = Off (will not disconnect line) 1.
Selects the line disconnect condition during recep-
tion. If the number of line errors exceed this setting,
the unit will disconnect the line.
2.
Selects the transmit condition of RTP/PIP or RTN/
PIN. (Available if No.73 ERROR DETECT is set to
"LINES") (See Note 1)
071 TOTAL ERROR 1 = 5%
2 = 10%
3 = 15%
4 = 20% Selects the transmit condition of RTP/PIP or RTN/
PIN.
(Available if No.73 ERROR DETECT is set to
"RATE") (See Note 2)
072 CONTINUOUS ERROR 1 = Off (unlimited)
2 = 3 lines/STD
3 = 6 lines/STD
4 = 12 lines/STD Selects the continuous total error criteria of Off/3/6
or 12 lines in Standard mode. If continuous total
error exceeds this setting, the unit will transmit
RTN/PIN. (Available if No.73 ERROR DETECT is
set to “RATE”.)
073 ERROR DETECT 1 = Lines
2 = Rate Selects the error detect condition Lines/Rate.
074 RTN RECEIVE 1 = Disconnect
2 = Continue Selects whether to disconnect the phone line or
continue when "RTN" is received.
Function Parameter Table
No. Parameter (see Note 3) Selections Function