Panasonic Panafax UF-895, Service Manual

Page: 154 / 342

Panasonic UF-885 / 895
154
Function Parameter Table
No. Parameter (see Note 3) Selections Function
000 MON/TEL DIAL 1 = Monitor
2 = TEL/DIAL Selects whether the machine starts to TX
automatically during On-Hook dialing.
(Monitor: Start to TX after pressing START)
(TEL/DIAL: Start to TX automatically)
001 ALARM STATUS 1 = OFF
2 = Timer (6 sec.)
3 = Constant Selects the No Paper or No Toner alarm status.
OFF : Alarm is disabled.
Timer : Alarm will shut off after 6 seconds.
Constant : Alarm will not stop until "STOP" is
pressed or the error is cleared/corrected.
002 STOP COMM. JRNL 1 = Off
2 = On Selects whether the machine prompts to print the
COMM. Journal when the printout condition is set
to INC and STOP is pressed during
communication.
003 CONTINUOUS POLL
(See Note 4) 1 = Off
2 = Stn (Tx only)
3 = Hub (Rx only) Selects whether the Continuous Polling feature is
enabled.
Stn:
When a document is placed on the ADF, the remote
machine can retrieve it automatically.
Hub:
When the polling command is initiated, the machine
will continuously poll documents from the remote
stations until it is interrupted by pressing "STOP".
004 NUMERIC ID SET 1 = Off (will not accept)
2 = On (accepts) Selects whether the machine accepts and allows to
set or change the Numeric ID.
005 Not Used
006 ID DISPLAY 1 = Number (Numeric ID)
2 = Chara (Character ID) Selects the priority of displaying the ID.
007 JNL COLUMN 1 = Preset station name
2 = Received ID Selects the contents of the ID to display on the
Journal.
008 MONITOR 1 = Off
2 = On Selects whether the Monitor is ON/OFF for
monitoring fax signals.
(FOR SERVICE USE ONLY)
009 DC LOOP 1 = Off (Normal)
2 = On (Off Hook) Selects a false Off Hook state for back to back
communication test.
010 TX LEVEL 00 = 0 dBm
~
15 = -15 dBm Selects the TX signal output level, 0 to -15 dBm in 1
dBm steps. (Refer to Chapter 4.3)
011 RX LEVEL 1 = -43 dBm
2 = -38 dBm
3 = -33 dBm
4 = -48 dBm Selects the receiving sensitivity of -33/-38/-43/-48
dBm.
(Refer to Chapter 4.3)
012 DTMF LEVEL 00 = 0 dBm
~
15 = -15 dBm
Selects the DTMF output level, 0 to -15 dBm in 1
dBm steps.
013 G3 RX EQL 1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dB Selects the cable equalizer for G3 reception mode,
0dB, 4dB, 8dB or 12dB.
014 G3 TX EQL 1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dB Selects the cable equalizer for G3 transmission
mode, 0dB, 4dB, 8dB or 12dB.
015
~
016
Not Used
017 TX START 1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps Selects the transmission modem start speed,
14400/12000/TC9600/TC7200/9600/7200/4800/
2400 bps.
Note:
This parameter is applicable only when
communicating with regular G3 machines.
When communicating with Super G3 (V.34)
machines, use Parameter No. 32.