Panasonic NR-B30FW1 Service Manual Download Page 4

Page: 4 / 67

Install and remove glass shelving securely to prevent risk of injury

When moving, raise the adjustable legs

Dragging the refrigerator will damage the floor. For flooring that may become easily damaged put a protective board in
place.

Do not scrape the metal rails

Take care of very hot parts

The compressor, pipes, etc. can be very hot during operation and directly after stopping. Also, the heater can be very hot
during power supply and immediately after power supply is stopped. Be careful not to burn yourself by touching very hot
parts.

Take care of very hot parts after welding

Pipes, etc., are very hot after welding. Be careful not to burn yourself by touching very hot parts.

Take care when filling/discharging refrigerant

Liquid refrigerant directly touching the skin may cause frostbite.

Take care of burrs

Be careful not to cut yourself on metal or plastic burrs.

Take care of condenser/evaporator fins

Be careful not to injure yourself on the fin edges.

Summary of Contents for NR-B30FW1




































































Search results

Summary of Contents for NR-B30FW1

Reviews:

Related manuals for NR-B30FW1

Brands by name

Popular brands

Panasonic NR-B30FW1, Service Manual

Search results

Summary of Contents for NR-B30FW1

Reviews:

Related manuals for NR-B30FW1

Brands by name

Popular brands