Panasonic NN-ST34HMRPH Service Manual Download Page 9

Page: 9 / 41

OPERATING SEQUENCE

The following is a description of component functions
during oven operation.

1. SETTING THE CLOCK

NOTE: You can set 12 hour clock.

2. CANCEL FUNCTION

Touch the Stop/Reset pad whenever you need to
cancel an entry or a function currently in use.
The display will either return to the last item entered
or to the clock.

COOKING

This oven has a CHILD LOCK feature

• TO SET CHILD LOCK

• Press Start 3 times in 10 seconds.

The clock will disappear. Actual time

will not be lost. “Child” is indicated in

the display.

• T

O CANCEL CHILD LOCK

• Press Stop/Reset 3 times in

10 seconds.

The clock will reappear in the display.

4-3

Stop/

Reset

Timer/

Clock

Timer/

Clock

Set the time

by pressing

Stop/

Reset

Desired

defrost

Desired

Start

Stop/

Reset

Desired

cooking time

Desired

cooking power

Start

2 STAGE

3. MICROWAVE COOKING

4. MULTI-STAGE MICROWAVE

5. AUTO WEIGHT DEFROST

time pads

program

weight

Stop/

Reset

Desired

Start

program

weight

reheat

6. AUTO WEIGHT REHEAT

7. CHILD LOCK

COOKING

Stop/

Reset

Desired

cooking time

Desired

cooking power

Desired

cooking time

Desired

cooking power

Start

Summary of Contents for NN-ST34HMRPH










































Search results

Summary of Contents for NN-ST34HMRPH

Reviews:

Related manuals for NN-ST34HMRPH

Brands by name

Popular brands

Panasonic NN-ST34HMRPH, Service Manual

Search results

Summary of Contents for NN-ST34HMRPH

Reviews:

Related manuals for NN-ST34HMRPH

Brands by name

Popular brands