Panasonic NN-ST34HMRPH Service Manual Download Page 20 | Manualshive

Page: 20 / 41

background image

5-9

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
CAPACITOR

HIGH VOLTAGE
DIODE

Measure the resistance.
(Ohm-meter scale: Rx1000)

• Terminal to terminal.

Measure the resistance.
(Ohm-meter scale: Rx1000)

• Terminal to case.

Measure the continuity (Forward).

(Ohm-meter scale: Rx10000)

Measure the continuity (Reverse).

(Ohm-meter scale: Rx10000)

Normal: Momentarily indicates

several ohms, and then
gradually returns to

Normal:

∞

Normal:

∞

Abnormal: Continuity.

NOTE: When testing the magnetron, be sure to install the magnetron gasket

in the correct position and be sure that the gasket is in good condition.

Antenna

Gasket

Chassis

Filament

10M ohms.

NOTE :

Some inexpensive meters
may indicate infinite
resistance in both direction.

*

Normal: Continuity.
Abnormal:

∞

*

«
...
18
19
20
21
22
...
»

Summary of Contents for NN-ST34HMRPH










































Reviews:

No comments

Related manuals for NN-ST34HMRPH

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 119

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 30

MS23A7013G Series

Brand: Samsung Pages: 220

Brand: Oster Pages: 2

TRIVECTION ZET3058

Brand: Monogram Pages: 2

Brand: NEFF Pages: 72

Brand: Jenn-Air Pages: 2

Brand: Calex Pages: 22

Brand: Smeg Pages: 22

Brand: Maytag Pages: 72

Brand: Cafe Pages: 24

Brand: Danby Pages: 33

Brand: NEFF Pages: 72

Brand: Zanussi Pages: 24

Brand: Zanussi Pages: 24

Brand: Electrolux Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands