Panasonic NE-2140 Service Manual Download Page 24 | Manualshive

Page: 24 / 57

background image

14.5. Upper antenna (Right and Left)

Upper antenna (Right and Left)

1. Remove 8 plastic clips holding ceiling plate and exhaust guides by

using flat screwdriver or the like.

2. Remove 2 screws holding upper antenna assy by inserting screwdriver

through the opening on the antenna as shown in figure.

14.6. Lower antenna (Right and Left)

Lower antenna (Right and Left)

1. To remove the floor shelf, insert a screwdriver through the openings on

the right and left sides of the oven cavity and carefully lift the floor
shelf as shown in figure.

2. Remove 2 screws holding lower antenna assy by inserting screwdriver

through the opening on the antenna as shown in figure.

23

Created with novaPDF Printer (

www.novaPDF.com

). Please register to remove this message.

«
...
22
23
24
25
26
...
»

Summary of Contents for NE-2140


























































Reviews:

No comments

Related manuals for NE-2140

Brand: Panasonic Pages: 109

Brand: Haden Pages: 12

Brand: GE Pages: 40

PT925SNSS - Profile 30" SC Convection Ovens

Brand: GE Pages: 68

Brand: NAPCO Pages: 19

Brand: Samsung Pages: 52

Brand: Panasonic Pages: 110

Brand: NEFF Pages: 48

Brand: Panasonic Pages: 33

Brand: Teka Pages: 14

GEMINI MASTER CHEF

Brand: Defy Pages: 12

Brand: DAEWOO ELECTRONICS Pages: 22

Brand: Scarlett Pages: 16

Brand: NEW POL Pages: 56

Brand: Hoover Pages: 52

Brand: Victoria Pages: 12

Brand: Daewoo Pages: 33

Combi Synergy R11021

Brand: Blodgett Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands