Panasonic NA-16VA1 Service Manual Download Page 5

Page: 5 / 46

-5-

2-5 Smart Beat Wash by variable rotation control

Previous washing method

New washing method (Variable rotation control)

The drum rotates at a constant speed. Therefore, due to different fabrics and weights of clothing
and insufficient penetration of water, dirt can not be beaten out by washing.

The laundry s movement inside the drum shall
be detected by 3D sensor, and the drum rotates
most suitable speed to realize proper beat washing.

Heavily clothes

Lightly clothes

If clothes shall not be

penetrated water enough

If clothes shall not be

penetrated water enough

45 r/min

Increased rotation
speed of the drum

Decreased rotation
speed of the drum

2-6 Wide angle water supply shower

New method (Conventional Wide-Angle Water Supply Shower)

Benefit of Wide-Angle Water Supply Shower

Washing

Process

Rinsing

Process

Quick Water
Penetration Effect

Water Supply Shower
During Rinsing Process

High Beating Wash and

Save The Time

Fine Rinsing Effect and

Save The Time

NA-16VX1/16VG1/14VA1

3D Sensor

All manuals and user guides at all-guides.com

Summary of Contents for NA-16VA1















































Search results

Summary of Contents for NA-16VA1

Reviews:

Related manuals for NA-16VA1

Brands by name

Popular brands

Panasonic NA-16VA1, Service Manual

Search results

Summary of Contents for NA-16VA1

Reviews:

Related manuals for NA-16VA1

Brands by name

Popular brands