Panasonic MINAS A6SG, Quick Start Manual

Page: 11 / 20

3.4 PNP wiring of the X4 connector
14
15
16
17
43
18
42
In case of open collector I/F
7
PULS2
SIGN1
SIGN2
GND
OA+
OA-
OB+
OB-
OZ+
OZ-
GND
CZ
SPR/TRQR/SPL
GND
P-ATL/TRQR
GND
N-ATL
SP
IM
4
3
1
2
5
6
13
21
22
48
24
25
19
49
23
1 kΩ
1 kΩ
PULS1
OPC2
OPC1
V
DC
12 V to 24 V
COM-
SIGNH1
SIGNH2
PULSH1
PULSH2
GND
FG
33
30
29
27
28
32
31
9
8
35
34
37
36
39
38
11
10
40
12
41
44
45
13
50
26
Z-phase output
(open collector)
3
PULS1
4
PULS2
X4
46
47
20 kΩ
2 kΩ
2 kΩ
20 kΩ
120 Ω
20 kΩ
2 kΩ
2 kΩ
20 kΩ
120 Ω
220 Ω
V
DC
R
5
SIGN1
6
SIGN2
220 Ω
R
1
OPC1
4
PULS2
220 Ω
24 V
DC
2 OPC1
6
SIGN2
220 Ω
2.2 kΩ
2.2 kΩ
(1) When you use the external
resistor with 12 V and 24 V
power supply
(2) When you do not use the
external resistor with 24 V
power supply
Positive direction torque limit input
(0 V to +10 V)
Negative direction torque limit input
(-10 V to +10 V)
Velocity monitor output
Torque monitor output
Command
pulse
input A
(Use with 500
kpulse/s or less.)
Divider
A-phase
output
B-phase
output
Z-phase
output
Command pulse input B
(Use with 8 Mpulse/s or less.)
Be sure to connect.
V
DC
12 V
24 V
Specifications
of R
820 Ω1/2 W
2 kΩ1/2 W
V
DC
-1.5
R + 220
10 mA
Servo-ON input
Gain switching input
Electronic gear
switching input 1
Control mode
switching input
Damping control
switching input 1
Alarm clear input
Positive direction
over-travel inhibition input
Negative direction
over-travel inhibition input
Servo-Ready output
Servo-Alarm output
Positioning complete output
External brake release output
Torque in-limit output
Zero speed detection output
Deviation counter
clear input
Command pulse
inhibition input
( : Twisted pair)
4.7 kΩ
220 Ω
2.2 kΩ
220 Ω
2.2 kΩ
<Remarks>
A6 Series standard type and communication type can not
be used Pin14,15,16,18. Please do not connect anything.
33.2 kΩ
20 kΩ
20 kΩ18.7 kΩ 20 kΩ
+
−
1000 P
1000 P
33.2 kΩ
20 kΩ
20 kΩ18.7 kΩ 20 kΩ
+
−
1000 P
1000 P
39 kΩ
470 P
470 P
470 P
39 kΩ
33 kΩ
+
−
COM+
INH
CL
SRV-ON
GAIN
DIV1
VS-SEL1
C-MODE
A-CLR
POT
NOT
S-RDY+
S-RDY-
ALM+
INP+
BRKOFF-
TLC
Z SP
INP-
ALM-
Signal inputs and outputs available on the X4 connector of the servo driver
3.4 PNP wiring of the X4 connector
13
34
36
38
33
29
39
37
35
7
8
9
50
24 Vcc
24 Vcc
0 Vcc
0 Vcc
To PNP inputs of PLC
PLC or trigger
switches
GND
S-RDY-
ALM-
INP-
STB
SRV-ON
INP+
ALM+
S-RDY+
COM+
NOT
POT
FG
From PNP outputs of
PLC
QS2001_V1.0_EN 11