background image

LH2H

Applicable standard

Safety standard

EN61010-1

Pollution Degree 2/Overvoltage Category III

EMC

(EMI)EN61000-6-4
Radiation interference electric field strength
Noise terminal voltage
(EMS)EN61000-6-2
Static discharge immunity

RF electromagnetic field immunity

EFT/B immunity
Conductivity noise immunity
Power frequency magnetic field immunity

EN55011 Group1 ClassA
EN55011 Group1 ClassA

EN61000-4-2    4 kV contact

8 kV air

EN61000-4-3    10 V/m AM modulation (80 MHz to 1 GHz)

10 V/m pulse modulation (90 MHz)

EN61000-4-4    2 kV (power supply line)
EN61000-4-6    10 V/m AM modulation (0.15 MHz to 80 MHz)
EN61000-4-8    30 A/m (50 Hz)

2. PC board mounting type

3. Common

Type

Item

PC board mounting type

Input method

Non DC voltage input

No. digits

7 digits

Rated operation voltage

3 V DC

Allowable operation voltage range

2.7 to 3.3 V DC

Current consumption

Max. 20 µA (max. 200 µA during reset input)

Measurement time range

0 to 999999.9h

0 to 9999h59.9m

Start 
input

Min. input signal width

200 ms

Input method

Non-voltage input using contacts or open collector connection

Input impedance

When shorted: Max. 10 k

When open: Max. 750 k

Residual voltage

Max. 0.5 V

Reset 
input

Min. input signal width

10 ms

Input method

Non-voltage input using contacts or open collector connection

Input impedance

When shorted: Max. 10 k

When open: Max. 750 k

Residual power

Max. 0.5 V

Break down voltage (initial)

Between charged and uncharged parts: 1,000 V AC for 1 minute.

Insulation resistance (initial)

Min. 100 M

 (measured at 500 V DC) Measurement location same as for break down voltage.

Type

Item

Panel mounting/PC board mounting types

Time accuracy

±100 ppm (25°C 

77°F

)

Vibration resistance

Functional

10 to 55 Hz (1 cycle/min.), single amplitude: 0.15 mm (10 min. on 3 axes)

Destructive

10 to 55 Hz (1 cycle/min.), single amplitude: 0.375 mm (1 hr. on 3 axes)

Shock resistance

Functional

Min. 98 m/s

2

 (4 times on 3 axes)

Destructive

Min. 294 m/s

2

 (5 times on 3 axes)

Operation temperature

–10 to +55°C 

+14 to +131°F

 (without frost or dew)

Storage temperature

–25 to +65°C 

–13 to +149°F

 (without frost or dew)

Ambient humidity

35 to 85% RH (non-condensing)

All Rights Reserved © C

OPYRIGHT

 Matsushita Electric Works, Ltd.

Summary of Contents for LH2H Series









Reviews: