Panasonic KX-UT670 Administrator'S Manual Download Page 100

Page: 100 / 250

4.6.4 VoIP Settings [Line 1]–[Line 6]

This screen allows you to change the VoIP settings that are specific to each line.

4.6.4.1 Quality of Service (QoS)

RTP Packet QoS (DSCP)

Description

Selects the DSCP level of DiffServ applied to RTP packets.

Value Range

0–63

Default Value

Configuration File Reference

DSCP_RTP_n (Page 178)

RTCP Packet QoS (DSCP)

Description

Selects the DSCP level of DiffServ applied to RTCP packets.

Value Range

0–63

Default Value

Configuration File Reference

DSCP_RTCP_n (Page 178)

100

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands