– 2 –
•
Clean the charge contacts of the handset and the charger with a soft, dry cloth
once a month. Clean more often if the unit is subject to grease, dust or high
humidity.
Otherwise the battery may not charge properly.
Handset battery information
After your Panasonic battery is fully charged:
Charging the battery
Place the handset on the charger and charge for
about 15 hours
before initial use.
•
The CHARGE indicator lights, a beep sounds and
“
Charging
” will be displayed.
•
Recharge the battery when:
– “
Recharge battery
” is displayed,
– “
” flashes on the display, or
– the handset beeps intermittently while it is in use.
•
If the battery has been discharged, the handset will
display “
Charge for 15HRS
” and “
” when you
place the handset on the charger. The handset will not
work. Keep charging.
– 3 –
The handset display shows the instructions as shown
on the right.
1
Base unit:
Press
(MUTE)
.
•
The MUTE indicator light flashes.
•
On the KX-FPG381, “
HS REGISTRATION
” is
displayed.
2
Handset:
#
Press the right soft key (
).
$
Wait until a long beep sounds and the display
shows the registered number. The registration
will be then complete.
•
The registered number “
[1]
” to “
[8]
” is shown on the top right of the display.
•
You can stop registration by pressing
(OFF)
on the handset and pressing
(MUTE)
on the base unit.
OK
SP
PRIVACY
[
-
]
Press MUTE on
base unit, then
OK on handset to
register handset
O K
Ex. Extension number 2
SP
PRIVACY
[
-
]
Handset
Registering
SP
PRIVACY
[
2
]
Handset [2]
Registered
Registration
!
This cordless handset must be registered to a KX-TG2700/KX-TG2720/
KX-TG2730/KX-TG2740/KX-TG2750/KX-TG2770/KX-FPG381 base unit.
The handset will be assigned the extension number at registration.
Only one handset can be registered at a time.
Make sure the base unit and the other handsets are not being used.
Registration must be completed within 1 minute.
•
The illustration of the base unit is the KX-TG2730.
– 4 –
Belt Clip
!
You can hang the handset on your belt or pocket using the belt clip.
To attach the belt clip
Optional Headset
!
Plugging an optional headset into the handset allows a hands-free phone
conversation. Please use only a Panasonic KX-TCA60/KX-TCA86/KX-TCA88/
KX-TCA91/KX-TCA92/KX-TCA98 headset.
To order, call the accessories telephone number on page 1.
Connecting the headset
Open the headset jack cover, and connect the headset to the headset jack as
shown.
H
Headset Jack
To remove the belt clip
While pressing the top of the clip (
A
),
pull the right edge in the direction of the
arrow (
B
).
CAUTION:
To reduce the risk of fire or injury to persons, read and follow these instructions.
1. Use only the battery(ies) specified.
2. Do not dispose of the battery(ies) in a fire. They may explode. Check with local waste
management codes for special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.
4. Exercise care in handling batteries in order not to short the battery to conductive
materials such as rings, bracelets, and keys. The battery and/or conductor may
overheat and cause burns.
5. Charge the battery(ies) provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
A nickel metal hydride battery that is recyclable
powers the product you have purchased. Please call
1-800-8-BATTERY for information on how to recycle
this battery.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR ANY TYPE OF MOISTURE.
Panasonic World Wide Web address: http://www.panasonic.com
for customers in the USA or Puerto Rico
Panasonic’s e-mail address for customer inquiries:
[email protected]
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Sales Company,
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985
For assistance, please call: 1-800-211-PANA(7262)
– 5 –
FCC and Other Information
!
When programming emergency numbers and/or making test calls to emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the call before
hanging up.
2. Perform such activities in the off-peak hours, such as early morning hours or late
evenings.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Privacy of communications may not be ensured when using this phone.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Operating near 2.4GHz electrical appliances may cause interference. Move away from
the electrical appliances.
CAUTION:
To comply with FCC RF exposure requirements, the handset should be carried with the
specific belt-clip provided for the handset to ensure compliance. Other non-tested belt-
clips or similar body-worn accessories may not comply, therefore, should be avoided.
This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section
68.316.
– 6 –
When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some
Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If
noise occurs, use an optional headset accessory or the speakerphone option (if
applicable) when using this phone. Consult with your audiologist or Hearing Aid
manufacturer about the availability of Hearing Aids which provide adequate shielding to
RF energy commonly emitted by digital devices.
Wall Mounting
!
The charger can be wall mounted. Connect the AC adaptor. Install screws using
the wall template below. Mount the charger (
#
). Slide it down (
$
) then slide
down to the right (
%
) until it is secured.
$
#
%
Wall Template
6.15 cm
(2
13
⁄
32
")
Screws
6.15 cm (2
13
⁄
32
")
For assistance, please call: 1-800-211-PANA(7262)
If you need assistance with the set-up or operation,
please call 1-800-211-PANA(7262)
CHARGE
Indicator
Charge Contacts
To Power
Outlet
Operation
Operating time
While in use (TALK)
While not in use (Standby)
While using the Reception Booster feature
Up to 3.5 hours
Up to 7 days
Up to 2.7 hours
When using the 2-Way Radio mode with the battery fully charged:
Operation
Operating time
While in use (TALK)
While not in use (Standby)
Up to 3.5 hours
Up to 9 hours
A
B
O K
[-]
Press MUTE on
base unit, then
OK on handset to
register handset
Soft key (
)
OK
(MUTE)
Button and
Indicator
•
The illustration of the headset is the KX-TCA88.
To cancel the handset registration, please see the KX-TG2700/KX-TG2720/
KX-TG2730/KX-TG2740/KX-TG2750/KX-TG2770/KX-FPG381 Operating
Instructions.
•
The AC adaptor is used as the main disconnect device, ensure that the AC outlet is
located/installed near the unit and is easily accessible.
For your future reference
Serial No.
Date of purchase
(found on the bottom of the unit)
Name and address of dealer
