21
KX-TG3661JXM/KX-TG3662JXM/KX-TG3668JXM/KX-TG3669JXM/KX-TGA365JXM
9 Service Mode
9.1.
Service Mode Function (for Base Unit with Cordless Handset)
9.1.1.
How to Clear User Setting
For detailed procedure, see Programming using the direct commands in the Operating Instructions feature code #144.
The service mode of KX-TG366x is operated by the Cordless Handset which has been linked the Base Unit.
3. Enter "9" "0" "0" "0" " ", then "SERVICE MODE" is displayed
4. Press the desired feature code (shown below).
2. Press [#].
To enter Service Mode:
Item
Key operation
Remarks
Software version
ROM=KXTG70 ver***
CNTTONE DET=
Remote turn
Continuous sound detection function (ON/OFF)
DTMF det=
DTMF detection integration time (Default: 50 ms)
BELL DET TIME=
RINGER detection integration time (Default: 600 ms)
TAD MONITOR=
Monitor setting when absence responding (Default: ON)
Slot diversity
Slot divercity funciton (Default: TX=on,RX=on)
Pause 035*100
Pause time setting (Default: 3.5 s=3500 ms)
Redial all erase
The data of the redial memory is cleared.
VOX DETECT=
VOX detection time (Default: 6s)
VOX SNS=
VOX detection sensitivity setting: HIGH/LOW (Default: HIGH)
VOX =
VOX detection function: ON/OFF (Default: ON)
System setup
KEYTONE SET=
KEY operation sound setting of base unit: ON/OFF (Default: ON)
AUTO DSCNCT=
Automatic line opens control setting (over parallel connected telephone):
ON/OFF (Default: OFF)
LINE MODE=
Line AGC control function: ON/OFF (Default: ON)
CPC MODE=
Disconnect line pulse detect function: ON/OFF (Default: OFF)
# 551 or [ ] [ ]
# 580 or [ ] [ ]
# 602 or [ ] [ ]
# 757 or [ ] [ ]
# 769 or [ ] [ ]
# 782 or [ ] [ ]
# 842 or [ ] [ ]
# 501 or [ ] [ ]
# 506 or [ ] [ ]
# 510 or [ ] [ ]
# 511 or [ ] [ ]
# 513 or [ ] [ ]
# 540 or [ ] [ ]
# 992 or [ ] [ ]
# 732 or [ ] [ ]
# 713 or [ ] [ ]
# 731 or [ ] [ ]
Remote turn=10
Units are reset to the Factory setting by this operation
(Erase recorded Voice messages, stored Phone numbers, Caller list and etc.).
Note:
L
This operation should not be performed for a usual repair.
L
Use the Cordless Handset which has been linked with the Base Unit for the factory setting of Base Unit.
"SERVICE MODE" is displayed on the LCD.
3. Select [ ] key in the menu of "All Initialize", and it becomes "Base Initialize".
For initializing Base Unit and Cordless Handset
4. When select [ ] key in the menu of "Base Initialize", then Base Unit and Cordless Handset are initialized.
After "complete" is shown on the display, press the [F1] key and it reactivates.
For initializing Cordless Handset
4.
When select
[#] key in the menu of "HS Initialize", then Cordless Handset is initialized.
After "complete" is shown on the display, press the [F1] key and it reactivates.
5. Delete All data of the Phonebook.
Press "#540" (system setup), then press key.
[
!
]
i
[#][
1
][
4
][
4
]
[
M
]
i
[*]
!
I
