Panasonic KX-TG2650N Operating Instructions Manual Download Page 62 | Manualshive

Page: 62 / 68

background image

62

Before Requesting Help

Problem

The handset or base unit
display goes to the standby
mode while viewing the
Caller List.

When a second call is
received during a
conversation, the unit does
not display the new caller’s
name and/or phone number.

You cannot page the
handset or the base unit.

You cannot redial by
pressing

(REDIAL/PAUSE)

or

(REDIAL)

.

“

Recharge battery

” is

displayed on the handset,
“

” flashes or the unit

beeps intermittently.

You charged the battery
fully, but “

Recharge

battery

” is still displayed

and/or “

” continues to

flash.

Remedy

•

Do not pause for over 60 seconds while
searching.

•

, or

(DIGITAL!SP-PHONE)

.

was pressed.

•

The line mode selection is incorrect. See
page 14.

•

The handset is too far from the base unit.

•

The handset or the base unit is engaged
in an outside call or is viewing the Caller
List/directory list. Try again later. If you
are using the base unit, wait until
“

Handset in use

” disappears.

•

If the last number dialed was more than
32 digits long, the number will not be
redialed correctly.

•

Access numbers entered after pressing

(TONE)

will not be included when

redialing.

•

The

(REDIAL/PAUSE)

button on the

handset has a double function as either
redial or pause. It will redial the last
number dialed if pressed at the outset of
a call (p. 20). If another number has
been dialed first, it will operate as a
pause button (p. 49).

•

Charge the battery fully (p. 11).

•

Clean the charge contacts and charge
again (p. 12).

•

Install a new battery (p. 58).

«
...
60
61
62
63
64
...
»

Summary of Contents for KX-TG2650N





































































Reviews:

No comments

Related manuals for KX-TG2650N

Brand: Panasonic Pages: 72

Brand: GE Pages: 84

Brand: Uniden Pages: 32

Brand: Auerswald Pages: 16

Brand: BELGACOM Pages: 34

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 56

KX-TG2551ALS, KX-TG2551NZS

Brand: Panasonic Pages: 56

KX-TG2553B - 2.4GHz DSS Cordless Phone

Brand: Panasonic Pages: 60

Brand: Panasonic Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands