Panasonic KX-TG2563B Operating Instructions Manual Download Page 23

Page: 23 / 68

Basic Operation

Hands-free Digital Duplex Speakerphone

For best performance, please note the following:

•

Talk alternately with the caller in a quiet room.

•

If the other party has difficulty hearing you, press

LOUD

to decrease the

speaker volume.

•

If the other party’s voice from the speaker cuts in/out during a conversation,
press

LOUD

to decrease the speaker volume.

To adjust the speaker volume (8 levels) while talking

To increase, press

LOUD

. To decrease, press

LOUD

To redial the last number dialed on the base unit

Press

(DIGITAL!SP-PHONE)

and press

(REDIAL/PAUSE)

To put a call on hold

Press

(HOLD/RINGER)

•

The DIGITAL SP-PHONE indicator flashes.

To release the hold

From the base unit, press

(DIGITAL!SP-PHONE)

From the handset, press

(TALK)

or lift the handset off the base unit.

•

If another phone is connected on the same line (p. 58), you can also release the
hold by lifting its handset.

Summary of Contents for KX-TG2563B





































































Search results

Summary of Contents for KX-TG2563B

Reviews:

Related manuals for KX-TG2563B

Brands by name

Popular brands

Panasonic KX-TG2563B, Operating Instructions Manual

Search results

Summary of Contents for KX-TG2563B

Reviews:

Related manuals for KX-TG2563B

Brands by name

Popular brands