Programmable Settings
42
Programming via direct commands
You can also program most features using “direct commands”—special codes that take
you directly to the feature you wish to program and allow you to select the desired setting.
There is no need to scroll through the unit’s menus.
Details of each feature can be found on the corresponding pages.
1
Press
{
MENU
}
.
2
Enter the desired feature code (shown below).
3
Enter the desired setting code (shown below).
L
This step may vary depending on the feature being programmed.
4
Press
{
Save
}
.
5
Press
{
OFF
}
to exit programming mode.
Direct commands chart
Feature
Feature code
Setting code
Page
Ringer volume
Line 1
{
1
}
{
1
}
{
1
}
{
1
}
: Low
{
2
}
: Medium
{
3
}
: High
{
0
}
: Off
page 36
Line 2
{
1
}
{
1
}
{
2
}
Ringer tone
Line 1
{
1
}
{
2
}
{
1
}
{
1
}
–
{
4
}
: Tone pattern 1–4
{
5
}
–
{
8
}
: Melody pattern 1–4
page 36
Line 2
{
1
}
{
2
}
{
2
}
Interrupt tone
{
1
}
{
3
}
{
1
}
: On
{
2
}
: 2 times
{
0
}
: Off
page 37
VM access
Line 1
{
3
}
{
1
}
Go to step 2 on page 34.
page 34
Line 2
{
3
}
{
2
}
Voice enhancer
{
5
}
{
1
}
: On
{
0
}
: Off
page 38
LCD contrast
{
0
}
{
1
}
{
1
}
–
{
6
}
: Level 1–6
page 38
Key tone
{
0
}
{
2
}
{
1
}
: On
{
0
}
: Off
page 40
Auto talk
{
0
}
{
3
}
{
1
}
: On
{
0
}
: Off
page 37
Set dial mode
{
0
}
{
5
}
{
1
}
{
1
}
: Pulse
{
2
}
: Tone
page 19
Set flash time
Line 1
{
0
}
{
5
}
{
2
}
{
1
}
{
1
}
: 700 ms
{
2
}
: 600 ms
{
3
}
: 400 ms
{
4
}
: 300 ms
{
5
}
: 250 ms
{
6
}
: 110 ms
{
7
}
: 100 ms
{
8
}
: 90 ms
page 39
Line 2
{
0
}
{
5
}
{
2
}
{
2
}
Set line mode
Line 1
{
0
}
{
5
}
{
3
}
{
1
}
{
1
}
: A
{
2
}
: B
page 39
Line 2
{
0
}
{
5
}
{
3
}
{
2
}
Line selection
{
0
}
{
5
}
{
5
}
{
0
}
: Auto
{
1
}
: Line 1
{
2
}
: Line 2 page 40
Store VM
access#
Line 1
{
0
}
{
7
}
{
1
}
{
1
}
Go to step 6 on page 33.
page 33
Line 2
{
0
}
{
7
}
{
1
}
{
2
}
TG2480C(e).book Page 42 Monday, December 26, 2005 2:49 PM
