Panasonic KX-TCD715ALM Operating Instructions Manual Download Page 13 | Manualshive

Page: 13 / 80

background image

Chapter 1

Ni-Cd battery operating time (optional)*

Up to about 12 hours (based on 800mA per hour)

Up to about 100 hours

13

Preparation

Battery information

After your batteries are fully charged:

•

Battery operating time may be shortened depending on usage conditions, such as:
— when viewing the Caller ID Caller List, or phonebook
— when talking in speakerphone mode and
— ambient temperature.

•

Clean the handset and the base unit charge contacts with a soft, dry cloth once a month.
Clean more often if the unit is subject to grease, dust or high humidity.

Otherwise the batteries

may not charge properly.

•

If the batteries are fully charged, you do not have to place the handset on the base unit until
“

” flashes. This will maximise the battery life.

•

The batteries cannot be overcharged.

*

Nickel cadmium (Ni-Cd) rechargeable batteries (AA size) are available.
When you replace the batteries, you must program the battery type selection (see page 70).

•

Read “Important Notice Concerning the Correct Use and Charging of Ni-MH (Ni-Cd) Batteries” on
page 71.

Operation

While in use (Talk)

While not in use (Standby)

Ni-MH battery operating time (included)

Up to about 20 hours

Up to about 200 hours

B a s e 1
1 0 N e w C a l l s

1 2 . 0 5 1 3 : 5 8

Turning the Power ON

#

The current connected base unit number

:

You can choose whether to display the base
unit number, handset number or no display
in the standby mode by programming (p. 64).

$

The number of new Caller ID calls received
(p. 26).

%

The current date and time:

After you set the date and time, the current
date/time will be displayed (p. 19).

To turn the power OFF

,

press and hold

until a beep sounds.

•

The display will go blank.

•

The handset will not ring.

Press and hold

.

•

After all the possible configurations briefly
appear, the display will change to the following.
Then the handset is in the standby mode.

#
$
%

KX-TCD715ALM-1Preparation1** 6/20/02 18:45 Page 13

«
...
11
12
13
14
15
...
»

Summary of Contents for KX-TCD715ALM

















































































Reviews:

No comments

Related manuals for KX-TCD715ALM

Brand: Aastra Pages: 2

Brand: Uniden Pages: 32

Brand: Alcatel Pages: 2

Brand: JabloCom Pages: 2

Brand: Talkswitch Pages: 65

Brand: Parkside Pages: 52

Brand: Krown Pages: 20

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 56

Brand: Aria Pages: 233

Brand: Olive Pages: 20

Brand: Vacom Pages: 38

Brand: Lectrosonics Pages: 28

Brand: Kimo Pages: 14

Brand: BT Pages: 84

DSU II SCS84125J

Brand: Comdial Pages: 128

Brand: Doro Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands