Panasonic KX-TCD500AL Operating Instructions Manual Download | Manualshive

Page: 5 / 68

background image

5

Prep

arat

ion

Important Information

Only use the power supply included with
the product.

Do not connect the AC adaptor to any
AC outlet other than the standard
AC220-240 V.
The apparatus is approved for use with
PQLV19AL power supply.

This apparatus is unable to make calls
under the following conditions:

•

The portable handset batteries need
recharging, or have failed.

•

During a mains power failure.

•

When the Key Lock is set to ON.

•

When the unit is in Direct Call mode
(only the Direct Call Number can be
made).

Do not open the base unit or handset
(other than to change the batteries).
This apparatus should not be used near
emergency/intensive care medical
equipment and should not be used by
people with pacemakers.
Care should be taken that objects do not
fall onto, and liquids are not spilled into
the unit. Do not subject this unit to
excessive smoke, dust, mechanical
vibration or shock.

Environment

Do not use this unit near liquid–for
example, near a bath tub, washbowl, sink,
etc. Damp basements should also be
avoided.
The unit should be kept away from heat
sources such as heaters, kitchen stoves,
etc. It also should not be placed in rooms
where the temperature is less than 5 °C or
greater than 40 °C.
The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is located/installed near the unit and
is accessible.

Battery Caution

1. Use only the specified batteries.

2.

Only use rechargeable batteries.

3. Do not mix old and new batteries.
4. Do not dispose of batteries in a fire, as

they may explode.

Check local waste management codes
for special disposal instructions.

5. Do not open or mutilate the batteries.

Released electrolyte from the batteries is
corrosive and may cause burns or injury

to the eyes or skin.

The electrolyte may be toxic if swallowed.

6. Exercise care in handling the batteries in

order not to short circuit the batteries with

conductive materials such as rings,
bracelets and keys.

The batteries and/or conductor may

overheat and cause burns.

7. Charge the batteries in accordance with

the information provided in this operating

guide.

Location

•

For maximum distance and noise-free
operation, place your base unit:

- Away from electrical appliances such

as TVs, radios, personal computers or
other phones.

- In a convenient, high, and central

location.

WARNING:

TO PREVENT THE RISK OF
ELECTRICAL SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN
OR ANY OTHER TYPE OF
MOISTURE.

500AL_e.book Page 5 Monday, June 30, 2003 3:17 PM

«
...
3
4
5
6
7
...
»

Summary of Contents for KX-TCD500AL





































































Reviews:

No comments

Related manuals for KX-TCD500AL

Brand: Talkswitch Pages: 32

VOIP-500 Series

Brand: Talkaphone Pages: 90

Brand: Uniden Pages: 60

Dialog 4222 Office

Brand: Aastra Pages: 2

Brand: GE Pages: 96

Payphone Contour 400

Brand: BT Pages: 36

Brand: Tala Pages: 4

Brand: Nortel Pages: 8

Brand: TechMatte Pages: 2

Brand: Parkside Pages: 95

Brand: Makita Pages: 28

Brand: Huawei Pages: 125

DTerm Series 80

Brand: NEC Pages: 2

Brand: Jabra Pages: 19

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands