3
Speed Dialer
“
Sp
2
Making/Answering Calls
“
Ma
n 1
2-A Making Calls
3-A Storing Phone Numbers in Memory
≥
For best operating performance, see
section 5-B.
Lighted handset keypad
The handset dialing buttons will light
when you press a button or lift the
handset off the base unit, and flash
when a call is received. The lights will go
out a few seconds after pressing a
button, lifting the handset, answering a
call, hanging up a call or leaving the
programming mode.
You can store up to 10 phone numbers in the handset. The dialing buttons (
(0)
to
(9)
) function as memory
stations. The TALK indicator light must be off before programming.
1
Press
(REDIAL/PAUSE/PROGRAM)
.
≥
The TALK indicator flashes.
2
Enter a phone number up to 22 digits.
3
Press AUTO
(fl)
.
4
Press a memory station number (
(0)
to
(9)
).
≥
A beep sounds.
≥
To store other numbers, repeat steps 1 through 4.
≥
If a pause is required for dialing, press
(REDIAL/PAUSE/PROGRAM)
where needed.
Pressing
(REDIAL/PAUSE/PROGRAM)
counts as one digit (4-D).
If you misdial
Press
(OFF)
to end storing.
¤
Start again
from step 1.
To erase a stored number
Press
(REDIAL/PAUSE/PROGRAM)
¤
¤
AUTO
(fl)
¤
the memory station
number (
(0)
to
(9)
) for the phone number to
be erased.
≥
A beep sounds.
Back side
Speaker
TALK Indicator
(‹)
,
(›)
,
CH
(fi)
(REDIAL/PAUSE/PROGRAM)
(OFF)
Microphone
(HOLD)
ate
TALK Indicator
AUTO
(fl)
(REDIAL/PAUSE/PROGRAM)
Memory
Station
Numbers
(OFF)
1
Press
and dial a phone number.
OR
To have a hands-free phone conversation,
press
and dial a phone number. When the
other party answers, talk into the microphone.
≥
The TALK indicator lights.
≥
If an alarm tone sounds, see section 5-E.
2
To hang up,
press
(OFF)
or place the handset on the base
unit.
≥
The TALK indicator light goes out.
(–––)
(–––)
To redial the last number dialed
Press or
¤
(REDIAL/PAUSE/PROGRAM)
.
To put a call on hold
Press
(HOLD)
.
≥
The TALK indicator on the handset and the
IN USE/CHARGE/HOLD indicator on the base unit
flash.
≥
If you put a call on hold for more than 6 minutes, an
alarm tone will sound. The call will be disconnected
after a total of 10 minutes.
To release the hold
Press
or
, or lift the handset off the base
unit.
≥
If another phone is connected on the same line
(5-D), you can also release the hold by lifting its
handset.
To adjust the receiver volume
(HIGH, MEDIUM or LOW) or speaker
volume (6 levels) while talking
Press
(‹)
or
(›)
while talking.
Receiver volume
(While using
)
≥
Each time you press
(‹)
or
(›)
, the volume level
will change from MEDIUM (preset) to HIGH or
LOW.
≥
When you replace the battery, the selected
receiver volume setting will return to the factory
set (MEDIUM). Reprogram if necessary.
Speaker volume
(While using
)
≥
Each time you press
(‹)
or
(›)
, the volume level
will change from level 1 to level 6. Your phone
comes from the factory set to level 3.
If noise interferes with the
conversation
Press CH
(fi)
to select a clearer channel or move
closer to the base unit.
(–––)
(–––)
(–––)
(–––)
(–––)
(–––)
one
o
Hands-free Digital Duplex Speakerphone
For best performance, please note the
following:
≥
Talk alternately with the caller in a quiet
room.
≥
If the other party has difficulty hearing you,
press
(›)
to decrease the speaker volume.
≥
If the other party’s voice from the speaker
cuts in/out during a conversation, press
(›)
to decrease the speaker volume.
≥
While talking using
, you can switch to
the hands-free phone conversation by
pressing
. To switch back to the
receiver, press
.
(–––)
(–––)
(–––)
PQQX13368ZA-BM 02.2.4 11:32 AM ページ 6
