background image

Paper Specifications

Paper which may be used with this unit must be within the specifications provided below.

Fanfold Paper

Width:

 102–254 mm (4–10 in.)

Quality and number of sheets:

Type of paper

Sheets

Weight

in lbs

in g/m²

Fine-quality paper

1

16–24

60–90

Non-carbon

2–4

11–14 (17

*1

)

41–53 (64

*1

)

Multi-layered with carbon

2

11–14 (17

*1

)

41–53 (64

*1

)

*1

Only for the last sheet

Note

In multi-layered paper with carbon, the carbon is equivalent to a sheet of paper.

"Weight in pounds" represents the weight of 500 [423 

´

 559 mm (17 

´

 22 in.)] sheets.

The printer will handle multipart papers up to 0.32 mm (0.013 in.). Up to 4 copies of 14 lb. chemical
release paper can be used.

Single Sheets

Width:

 102–297 mm (4–11.7 in.)

Height:

 127–363 mm (5–14.3 in.)

Weight in pounds (g/m²):

 53–90 g/m² (14–24 lbs)

Note

Paper should be within operating temperature and humidity ranges at least 24 hours prior to use.

Envelopes

#6 and #10 size envelopes are recommended. Since envelopes vary in size, paper weight and construction,
we cannot guarantee print quality and paper handling for all types of envelopes.

Note

To optimize print quality printing should not occur in areas where the edges overlap.

Operating Instructions

37

Appendix

Summary of Contents for KX-P1121E












































Reviews: