PS
QW2583ZA
KK0707ME0 (M)
Bluetooth Ver. 2.0 + EDR
Document Version 2007-06
Installation
Installing the KX-NT307 Bluetooth Module
1) Disconnect the AC adaptor and/or Ethernet cable
from the IP proprietary telephone (IP-PT) and make
sure that the power is off.
CAUTION:
Before touching the module, discharge static
electricity by touching ground. Otherwise, this
module may malfunction due to the static
electricity.
2) Remove the screw covers with a pointed object and
the two screws from behind the IP-PT’s LCD display,
as shown below.
3) Detach the back cover using a pointed object via the
hole situated at the top of the cover (
C
).
4) Install the KX-NT307 Bluetooth Module to the
designated slot (
E
), as shown below.
5) Reattach the back cover with the screws from step 2
and reattach the screw covers. Then reconnect the
AC adaptor and/or Ethernet cable to the IP-PT.
Trademark:
The Bluetooth word mark and logos are owned by the Bluetooth
SIG, Inc. and any use of such marks by Matsushita Electric
Industrial Co., Ltd. is under licence.
Note:
In these Installation Instructions, the suffix of each model
number is omitted.
© 2007 Panasonic Communications Co., Ltd. All Rights
Reserved.
Operation
This module allows for third party Bluetooth headsets to
be used with the KX-NT343, KX-NT346, and KX-NT366
IP-PTs. It is not guaranteed that all features of the
Bluetooth headset can be performed when used with this
module.
•
One Bluetooth headset may be registered to the module.
•
This module supports Bluetooth devices that use the
headset profile (HSP) and hands-free profile (HFP).
Registering the Bluetooth headset
1) Press
(PAUSE)
→
→
(ENTER)
.
2) From the Bluetooth headset, set it to pairing mode by
following the instructions provided with the Bluetooth
headset.
3) Enter the Passkey by following the instructions
provided with the Bluetooth headset, or by confirming
with the manufacturer of the Bluetooth headset, and
press
(ENTER)
.
•
When registration has been completed, a confirmation
tone will be heard.
•
If a warning tone is heard, confirm the headset’s passkey,
press
(CANCEL)
, and perform step 3 again.
4) Press
(PAUSE)
to exit programming mode.
•
After headset registration is complete, turn the headset
off then on again.
•
When the Bluetooth headset establishes a link to the
unit, the Message/Ringer Lamp flashes green for 3
seconds.
Note:
•
If you have already registered a Bluetooth headset that you
did not wish to register, overwrite the headset by registering
the correct headset.
•
For more information about confirmation and warning tones,
refer to the User Manual of the PBX.
Assigning a Headset Mode button
A CO button can be assigned as a Headset Mode button.
1) Press
(PAUSE)
→
the desired CO button
→
→
(ENTER)
.
•
The Headset Mode button can be used to turn Headset
Mode on and off. A CO button assigned as the Headset
Mode button displays Headset Mode status as follows:
Red:
Headset Mode on
Off:
Headset Mode off
•
When Headset Mode is off, the Bluetooth headset can be
used to answer calls or redial. In this case, Headset Mode
will turn on automatically, and will turn off after you hang up.
Confirming the ID of the Bluetooth headset and de-
registering the Bluetooth headset
1) Press
(PAUSE)
→
→
(ENTER)
.
•
Confirm that the displayed ID is the ID of your Bluetooth
headset. For information regarding the ID of your
Bluetooth headset, refer to the operating instructions of
the Bluetooth
headset
.
•
If you do not wish to perform de-registration, press
(CANCEL)
3 times.
2) Press
(ENTER)
to de-register the Bluetooth
headset.
3) Press
(PAUSE)
to exit programming mode.
D
C
E
CANCEL
CANCEL
Panasonic KX-NT307
Bluetooth Module
Installation Instructions
NT307M-b5.fm Page 1 Tuesday, May 22, 2007 11:43 AM
www.voicesonic.com
Phone: 877-289-2829
