Bit No.
DIS/DTC
Standard
setting
DCS
21, 22, 23
(0, 0, 0)
(0, 0, 1)
(0, 1, 0)
(1, 0, 0)
(0, 1, 1)
(1, 1, 0)
(1, 0, 1)
(1, 1, 1)
Minimum scan line time capability of the
receiver
20 ms at 3.85 l/mm: T7.7 = T3.85
40 ms at 3.85 l/mm: T7.7 = T3.85
10 ms at 3.85 l/mm: T7.7 = T3.85
5 ms at 3.85 l/mm: T7.7 = T3.85
10 ms at 3.85 l/mm: T7.7 = 1/2 T3.85
20 ms at 3.85 l/mm: T7.7 = 1/2 T3.85
40 ms at 3.85 l/mm: T7.7 = 1/2 T3.85
0 ms at 3.85 l/mm: T7.7 = T3.85
Minimum scan line time
20 ms
40 ms
10 ms
5 ms
0 ms
24
Extend field
1
Extend field
25
2400 bit/s handshaking
0
2400 bit/s handshaking
26
Uncompressed mode
0
Uncompressed mode
27
Error correction mode
0
Error correction mode
28
Set to "0".
0
Frame size 0 = 256 octets 1 =
octets
29
Error limiting mode
0
Error limiting mode
30
Reserved for G4 capability on PSTN
0
Reserved for G4 capability on
31
Unassigned
0
32
Extend field
1
Extend field
33
(0)
(1)
Validity of bits 17, 18
Bits 17, 18 are valid
Bits 17, 18 are invalid
0
Recording width
Recording width indicated by
18
Recording width indicated by
field bit / information
34
Recording width capability 1216 picture
elements along scan line length of 151 ±
mm 1%
0
Middle 1216 elements of 1728
elements
35
Recording width capability 864 picture
elements along scan line length of 107 ±
mm 1%
0
Middle 864 elements of 1728
elements
36
Recording width capability 1728 picture
elements along scan line length of 151 ±
mm 1%
0
Invalid
37
Recording width capability 1728 picture
elements along scan line length of 107 ±
mm 1%
0
Invalid
38
Reserved for future recording width
capabilities.
0
39
Reserved for future recording width
capabilities.
0
40
Extend field
1
Extend field
41
Semi super time / mm
1
42
Semi super time / mm
0
43
Super time
0
152
Summary of Contents for KX-FT71LA-B
