Panasonic KX-FP362CX Service Manual Download

Page: 28 / 194

Disconnect the power cord and the telephone line cord.

Open the front cover (

) by pulling up the centre part (

Release the back cover by pushing the green button (

) on

the right side of the unit.
OR
Release the back cover by pushing the green lever (

) in the

unit.

Open the back cover (

Remove the ink film (

Clean the thermal head (

) with a cloth moistened with

isopropyl rubbing alcohol, and let it dry thoroughly.

Caution:

To prevent a malfunction due to static electricity, do not
use a dry cloth and do not touch the thermal head
directly.

Reinstall the ink film and close the co vers. (See step 4 to 6 )
Refer to INSTALLING THE INK FILM (P.15)

Clnnect the power cord and the telephone line code.

4.4.2. THERMAL HEAD

If smudges or black/white lines appear on a copied or received document, check whether there is dust on the thermal head and
roller shaft, and clean the thermal head to remove the dust.

KX-FP362CX

Summary of Contents for KX-FP362CX



































































































































































































Search results

Summary of Contents for KX-FP362CX

Reviews:

Related manuals for KX-FP362CX

Brands by name

Popular brands

Panasonic KX-FP362CX, Service Manual

Search results

Summary of Contents for KX-FP362CX

Reviews:

Related manuals for KX-FP362CX

Brands by name

Popular brands