Panasonic KX-FP362CX Page 15 Service Manual Download

Page: 15 / 194

Open the front cover (

) by pulling up the center part (

Release the back cover by pushing the green button (

) on

the right side of the unit.
OR
Release the back cover by pushing the green lever (

) in the

unit.

Open the back cover (

Insert the gear with the blue core of the front ink film roll (

)

into the left slot of the unit (

). Insert the rear ink film roll

(

The ink film is safe to touch, and will not rub off on your
rands like carbon paper.

Turn the gear with the blue core (

) in the direction of the

arrow.

Make sure that the ink film is wrapped around the blue core

(

) at least once.

First close the back cover securely (

) by pushing down on

the dotted area at both ends (

). Then close the front cover

securely (

3.3.4. INSTALLING THE INK FILM

KX-FP362CX

Summary of Contents for KX-FP362CX



































































































































































































Search results

Summary of Contents for KX-FP362CX

Reviews:

Related manuals for KX-FP362CX

Brands by name

Popular brands

Panasonic KX-FP362CX, Service Manual

Search results

Summary of Contents for KX-FP362CX

Reviews:

Related manuals for KX-FP362CX

Brands by name

Popular brands