Panasonic KV-S6050W, Service Manual

Page: 182 / 267

CN2010(MOTHER) - CN501(RELAY [BACK])
Pin No. Signal Name Description
4 RXD0 RXD0 for Pre Imprinter
5 IMP RST Imprinter Reset
6 PREIMPSP
Start Pulse for
Post imprinter Door Sensor
7 +5V +5V
8 38V 38V
9 38V 38V
10 +12V +12V
11 GND Ground
12 GND Ground
13 CLK40K Clock output 40kHz
14 +5V +5V
15 DFGAIN
16 +24V +24V
17 GND Ground
18 SIZE 0 Paper Size Sensor 0
19 SIZE 1 Paper Size Sensor 1
20 SIZE 2 Paper Size Sensor 2
21 SIZE 3 Paper Size Sensor 3
22 SIZE 4 Paper Size Sensor 4
23 SIZE 5 Paper Size Sensor 5
24 SIZE 6 Paper Size Sensor 6
25 SIZE 7 Paper Size Sensor 7
26 SIZE 8 Paper Size Sensor 8
27 DOOR IMP Imprinter Door Status
28 +5V +5V
1 CTS0 CTS0 for Pre Imprinter
2 TXD0 TXD0 for Pre Imprinter
3 RTS0 RTS0 for Pre Imprinter
Pin No. Signal Name Description
1 NEUTRAL Neutral
2 - N.C.
3 LIVE Live
Power Switch - AC Inlet
CN2009(MOTHER) - CN504(RELAY [BACK])
Pin No. Signal Name Description
4 START LED Starting LED
5 RETARD Retard
6 FB DOOR Flat Bed Door Status
7 END LED Ending LED
8 END POS Ending Position
9 HOPP MID Hopper MID
10 HOPP POS Hopper Position
11 PAPER RF LED Current Control
12 PAPER Paper
13 START POS Paper Position
14 DBL FEED Double Feed
15 +12V
16 SIZE 0 Paper Size LED 0
17 SIZE 1 Paper Size LED 1
18 SIZE 2 Paper Size LED 2
19 SIZE 3 Paper Size LED 3
20 SIZE 4 Paper Size LED 4
21 SIZE 5 Paper Size LED 5
22 SIZE 6 Paper Size LED 6
23 SIZE 7 Paper Size LED 7
24 SIZE 8 Paper Size LED 8
25 +5V +5V
26 +5V +5V
1
GND Ground
2 GND Ground
3
- N.C.
+12V
CN2008(MOTHER) - CN001(CCD Board)
Pin No. Signal Name Description (S6055)
4 GND Ground
5 LAMP SW1 LAMP SW1
6 LAMP SW2 LAMP SW2
7 CCDDET2 CCD Board detect 2
8 AGND Analog Ground
9 AGND Analog Ground
10 CCD ODD CCD ODD DATA
11 AGND Analog Ground
12 CCD EVEN CCD EVEN DATA
13 GND Ground
14 CCDDET1 CCD Board detect 1
15 VCC +5V
16 DAC DATA DAC Data
17 DAC CLK DAC Clock
18 CCD CLMP CCD Clamp
19 ANLG LD Analog Control Signal Strobe
20 GAIN2 GAIN 2
21 GAIN1 GAIN 1
22 GND Ground
23 CCD ROG CCD ROG
24 CCD P1 CCD DATA Clock 1
25 CCD P2 CCD DATA Clock 2
26 GND Ground
27 GND Ground
28 CCD RST CCD RESET pulse
29 GND Ground
30 CCD SH CCD Sample Hold
31 GND Ground
32 GND Ground
33 -5V -5V
34 +12V +12V
1
+24V +24V
2 +24V +24V
3
GND Ground
CN503(RELAY [BACK]) - Imprinter (Option)
Pin No. Signal Name Description
4 RXD0
RXD0 for imprinter serial interface
5 IMP RST Imprinter Reset
6 SP Start Signal
7 VCC +5V
8 +38V +38V
9 +38V +38V
10 +12VS +12V
11 GND Ground
12 GND Ground
1 CTS0
CTS0 for imprinter serial interface
2 TXD0
TXD0 for imprinter serial interface
3 RTS0
RTS0 for imprinter serial interface
CN802(POWER) - CN861(DC-DC)
Pin No.
(CN802)
Signal Name Description
4 GND Ground
5 GND Ground
6 GND Ground
7 +24V(SWITCHED) +24V(Switched)
8 +24V(SWITCHED) +24V(Switched)
9 +24V +24V
10 +24V
+24V
11 STB +24V Enable
1 -5VOVP -5V Over Voltage Detection
2 +3.3VOVP +3.3V Over Voltage Detection
3 +5VOVP +5V Over Voltage Detection
Pin No.
(CN861)
8
7
6
5
4
3
2
1
11
10
9
Pin No. Signal Name Description
1 GND Ground
2 CARRIAGE Carriage
3
-
N.C.
4 VCC +5V
CN2011(MOTHER) - CN516
(CARRIAGE HOME DETECTOR)