Panasonic K-EW114L03AE Operation Manual Download

Page: 81 / 82

5 Alarm

Click alarm function, you can see an interface is shown as in Figure 5-1

Here you can set device alarm type and alarm sound setup.

Figure 5-1

Please refer to the following sheet for detailed information.

Type

Parameter

Function

Alarm

Type

VMD

System alarms when VMD alarm occurs,

Disk full

System alarms when disk is full.

(K-EW214L01E, K-EF234L01E)

Disk Error

System records alarm info when disk error

happens.

(K-EW214L01E, K-EF234L01E)

Tampering

System alarms when tampering alarm occurs.

Illegal Access

System alarms when illegal access occurs,

Operation

Prompt

System automatically pops up alarm dialogue box.

Alarm

Tone

Play Alarm Tone When alarm occurs, system auto generates alarm

audio. The audio supports customized setup.

Tone Path

Here you can specify alarm sound file.

Summary of Contents for K-EW114L03AE



















































































Search results

Summary of Contents for K-EW114L03AE

Reviews:

Related manuals for K-EW114L03AE

Brands by name

Popular brands

Panasonic K-EW114L03AE, Operation Manual

Search results

Summary of Contents for K-EW114L03AE

Reviews:

Related manuals for K-EW114L03AE

Brands by name

Popular brands