Panasonic i-Pro WV-SW355 Installation Manual Download Page 28 | Manualshive

Page: 28 / 52

background image

28

v

Connect a LAN cable (category 5e or better, straight, STP*) to the network connector.

* PAL model only

b

Connect the power cable.

• When using 12 V DC power supply*

1

Connect the output cable of the AC adaptor to the 2P power cable.

• When using PoE (IEEE802.3af compliant)

Connect a LAN cable (category 5 or better, straight, STP*

2

) between a PoE device (such as a

hub) and the network connector of the camera.

*1 FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.

*2 PAL model only

Connect the power cord.

  •  Use all 4 pairs (8 pins) of the LAN cable.
  •  The maximum cable length is 100 m {328'}.
  •  Make sure that the PoE device in use is compliant with IEEE802.3af standard.
  •  When connecting both the 12 V DC power supply and the PoE device for power supply, PoE

will be used for power supply.

• When the LAN cable is disconnected once, reconnect the cable after about 2 seconds. When

the cable is quickly reconnected, the power may not be supplied from the PoE device.

«
...
26
27
28
29
30
...
»

Summary of Contents for i-Pro WV-SW355





















































Reviews:

No comments

Related manuals for i-Pro WV-SW355

EF 100-400mm f/4.5-5.6L IS USM

Brand: Canon Pages: 9

EF-M 18-55mm f3.5-5.6 IS STM

Brand: Canon Pages: 12

Brand: D3D Pages: 4

Brand: Samsung Pages: 1

iPOLiS SNP-3120

Brand: Samsung Pages: 1

Brand: Samsung Pages: 7

Brand: Samsung Pages: 23

iPOLiS SNP-3120

Brand: Samsung Pages: 2

iPolis SNO-5080R

Brand: Samsung Pages: 60

Brand: S&S Pages: 12

Brand: Uniden Pages: 32

Brand: Panasonic Pages: 4

Brand: Brickcom Pages: 40

Brand: Lasertec Pages: 12

Brand: Tasco Pages: 24

smc Pentax-D FA Macro 100mm f/2.8

Brand: Pentax Pages: 12

Brand: i-PRO Pages: 28

Brand: NEO Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands