background image

1.2 Specifications

9

Interface

Twisted pair port 1-4: RJ45 connector (*1)

 Transmitting and receiving networks system

   IEEE802.3       10BASE-T

   IEEE802.3u     100BASE-TX

   IEEE802.3ab   1000BASE-T

Twisted pair port 5,6: RJ45 connector

 Transmitting and receiving networks system

   IEEE802.3       10BASE-T

   IEEE802.3u     100BASE-TX

   IEEE802.3ab   1000BASE-T

 (*1) Energy Efficient Ethernet function

   IEEE802.3az(LPI)

SFP extension slot 5,6port

 Transmitting and receiving networks system

   IEEE802.3z      1000BASE-SX/1000BASE-LX

  *Select either RJ45 or SFP for use

  SFF-8472 (DMI:Diagnostic Monitoring Interface)

Console port: RJ45 connector

 RS-232C(ITU-TS V.24)

Switching mode

Store and Forward method:  Forwarding rate

  10BASE-T: 

Max. 14,880 pps/port

  100BASE-TX: 

Max. 148,800 pps/port

  1000BASE-T: 

Max. 1,488,000 pps/port

MAC Address table: 

Max. 16K entry/unit

Buffer: 2.0Mbyte/unit

* EAP frame, BPDU frame transmission

Link Aggregation

IEEE802.3ad

Configurable up to 3 groups (Max. 6 ports per group)

VLAN

IEEE802.1Q tagging VLAN protocol compatible

(Max. 256 groups including the default VLAN)

Port based VLAN, Internet Mansion function

QoS

IEEE802.1p compatible, Supports 8 priority queues

Management method

ZEQUO assist Plus (Supplied CD-ROM), SNMP v1/v2c/v3, Telnet

SSH v2, Console, WEB control screen (Scheduled to be supported)

Power supply function

Ports 1 to 4 support the IEEE802.3at/af compatible power supply function.

Maximum power supply: 30 W per port, 62 W in total

Power supply method

Alternative A (Using 1,2,3,6 pin)

Others

STP/RSTP/MSTP

Supports the IEEE802.1X authentication (MAC-based, port-based)

MAC authentication, WEB authentication, Triple authentication,

STEP authentication, IEEE802.1X supplicant,

Port monitoring, Ring protocol, IGMP snooping,

Loop detection/shutoff function, Storm control, DSCP mapping function,

Login RADIUS function, DHCP client function,

PoE scheduler function, PoE auto reboot function, 

Port grouping function, Multi-cast address group registration function

Power supply

AC 100-240 V, 50/60 Hz, 2.5 A

Power consumption

Normally, Max. 83.2 W (12.4 W when not supplying power), Min. 9.9 W

Summary of Contents for GA-ML16TPoE+

























Reviews: