1
n
MEUML-FX301 V1.1
Thank you for purchasing products from Panasonic Electric Works SUNX
Co., Ltd. Please read this Instruction Manual carefully and thoroughly for
the correct and optimum use of this product. Kindly keep this manual in a
convenient place for quick reference.
1
For further details on the fiber sensor amplifier, please refer to our
Web site:
www.panasonic-electric-works.com
, or contact our office.
This product has been developed / produced for industrial use only.
Make sure to carry out wiring with the power OFF.
Verify that the supply voltage including the ripple is within the rating.
Do not connect the sensor to voltage that exceeds the rated range or
directly to an AC power supply: it may damage or burn the sensor.
Incorrect wiring or short-circuiting the load may damage or burn the
sensor.
When the emitting level function is turned from OFF to ON for any level,
the output may be unstable. Do not use the output control for at least
0.5s after starting emission. (See “PRO1” on page 6.)
If power is supplied from a commercial switching regulator, ensure that
the frame ground (F.G.) terminal of the power supply is connected to an
actual ground.
In case noise generating equipment (switching regulator, inverter motor,
etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
Do not run the wires together with high-voltage lines or power lines or put
them in the same raceway. This can cause malfunction due to induction.
Do not use during the initial transient time (0.5s) after the power supply is
switched on.
This sensor is suitable for indoor use only.
You can extend the cable up to 100m max. with 0.3mm
2
or more cable. If
5 to 8 units are connected in cascade, the limit is 50m; for 9 to 16 units in
cascade, 20m. However, in order to reduce noise, make the wiring as
short as possible.
Note that extending the cable increases the residual voltage.
Be sure to use the optional quick-connection cable when connecting to
the connector type sensor FX-301(P).
Avoid dust, dirt and steam.
Take care that the sensor does not come in contact with oil, grease,
organic solvents such as thinner, etc., strong acid, or alkaline.
Do not use this sensor in an environment containing inflammable or
explosive gases.
Never disassemble or modify the sensor.
You may break the spring hook if you do not follow the mounting
instructions carefully.
How to mount the amplifier
How to remove the amplifier
INSTRUCTION MANUAL
Photoelectric Sensor
Digital Fiber Sensor
FX-301
Series
1
The digital fiber sensor FX-301(P) has been modified since production in June,
2004. Hence, this instruction manual has been changed to reflect the modifica-
tions.
WARNING
• Never use this product as a sensing device for personnel protection.
• In case of using sensing devices for personnel protection, use
products which meet laws and standards, such as OSHA, ANSI or IEC
etc., for personnel protection applicable in each region or country.
1
CAUTIONS
2
PART DESCRIPTION
No.
Part
Description
Q
Operation indicator
(orange)
Lit when output is on.
W
Stability indicator
(green)
Lit when detection is stable according
to the parameters set.
E
RUN mode indica-
tor (green)
Lit when FX-301 is in RUN mode.
R
TEACH mode indi-
cator (yellow)
Lit when FX-301 is in TEACH mode.
T
ADJ mode indicator
(yellow)
Lit when FX-301 is in ADJ (threshold
value adjustment) mode.
Y
Digital display (red)
Displays incident light intensity under
normal circumstances. Also displays
sub-modes and settings.
U
L/D mode indicator
(yellow)
Lit when FX-301 is in L/D mode (Light-
ON, Dark-ON) mode.
I
TIMER mode indica-
tor (yellow)
Lit when FX-301 is in TIMER mode.
O
PRO mode indica-
tor (yellow)
Lit when FX-301 is in PRO mode.
P
Jog switch
The jog switch allows you to select the
various sub-modes and confirm set-
tings.
{
Mode key
The mode key allows you to switch
from mode to mode, or to cancel set-
tings and return to RUN mode.
3
MOUNTING
1
Fit the spring hook on a 35mm DIN rail and
push forward.
2
Slip the front part of the mounting section over
the DIN rail and release.
1
Push the amplifier forward
2
Lift up the front part of the amplifier.
RUN
TEACH
ADJ
MODE
CANCEL
PUSH
TIMER
W E
O
I
Y U
T
R
P
Q
{
Ԙ
ԙ
35mm
1
2
