Panasonic FV-0511VKL2 Installation Instructions Manual Download Page 8

Page: 8 / 12

Base PCB box

Slot

INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES)

INSTALLATION (NEW CONSTRUCTION)

1. Remove the connector cover

2. Plug in the specified devices to Base PCB box and fix to the slot, till hear the sound installed in place.

from position , or .

, and . Position can only be used with Multi-Speed module (model FV-0511VKSL2 already have

this control installed), position and can be used for any of the other optional control modules.

Connector

cover

Squeeze tabs on the Clasp to
remove. Squeeze, insert and
release the tabs on Clasp to replace.

Clasp

1. Disconnect plug connector from receptacle and

remove adaptor from fan body by removing the

machine screw (M4X8) before installation. (Fig.1)

IMPORTANT:

Remove the tape from damper and adaptor

before installation. As shown below:

The fan position between joists from 16" to 24"

on center can be adjusted flexibly.

2. Bend down 4 tabs for positioning, install the

Flex-Z Fast bracket to joists by drilling 2 tapping

screws which have been fixed on it. (Fig.2)

3. Adjust the length of Flex-Z Fast bracket as the

spacing between joists, and install to joists by

drilling the other 2 tapping screws which have

been fixed on it. (Fig.3)

4. Remove junction box cover and secure conduit

or stress relief to junction box knock-out hole.

(Fig.4)

6. Install the adaptor to Flex-Z Fast bracket by

using 2 self-drilling screws. (Fig.4)

5. Install a circular duct and secure it with clamps,

or ties and seal it with mastic or approved foil tape.

A 4 or 6 inch circular duct is needed to connect to

relevant part of adaptor. (Fig.4)

Please wear gloves during the installation

work as follow.

CAUTION

Tape

Adaptor

Damper

Fig.2

2 Tapping screws

(ST4.2X20)

Bend down

4 tabs

Joist

Fig.3

Joist

2 Tapping screws

(ST4.2X20)

2 Self-drilling screws

Knock-out

hole

Junction box

cover

Conduit

Circular duct

Mastic or

approved

foil tape

Fig.4

You can purchase the specified Plug ‘N Play devices that are explained on page 6-7 and install them in positions

English

Fan body

Adaptor

Fig.1

Machine screw

(M4X8)

Receptacle

Plug connector

Summary of Contents for FV-0511VKL2













Search results

Summary of Contents for FV-0511VKL2

Reviews:

Related manuals for FV-0511VKL2

Brands by name

Popular brands

Panasonic FV-0511VKL2, Installation Instructions Manual

Search results

Summary of Contents for FV-0511VKL2

Reviews:

Related manuals for FV-0511VKL2

Brands by name

Popular brands