background image

ENGLISH - 3

Read this first!

WARNING

Ask a qualified technician or your dealer to perform the installation work.

Inadequate installation may result in fire, electric shocks, or falling of the projector.

 

z

Follow the instructions specified in “Installation” of this manual, and perform secure installation.

 

z

To be installed by qualified personnel only.

 

z

Do installation in accordance with your country regulations.

Install the certified wiring circuit breaker (breaker with rated current of 16 A or less) in a location that 

can be easily reached.

Insufficient capacity of the indoor wiring for the power supply or incorrect installation may result in a fire or 

electric shock.

 

z

If anything abnormal occurs, immediately shut off the power supply of the indoor wiring with the certified 

wiring circuit breaker.

Make sure that your footing is safe and secure during installation.

 

z

If your footing is not secure, you may fall down or drop the projector, and an injury may result.

Install the product in a way that is suitable for the structure and material of the installation location.

Performing the installation work in an incorrect way may cause a fire, electric shock, or falling accident.

Make sure that the mounting work is carried out by two or more persons.

Failure to observe this may result in damage or deformation of the projector, serious accidents or injury caused 

by falling.  

Do not mount the product to a wall or ceiling that is unable to withstand the weight.

Doing so may cause injury due to falling or a fire or electric shock.

Do not install the projector in a passageway.

Bumping into the projector or tripping on the power cord may cause a fire, electric shock, or injury.

 

z

When installing the projector in a passageway, take measures to prevent physical contact with the projector 

by setting up a fence or similar things.

Do not install the product in a location where the intake and exhaust of the projector will be blocked.

Heat accumulating inside the projector may cause a fire.

Do not set up the projector in humid or dusty places or in places where the projector may come into 

contact with oily smoke or steam.

Using the projector under such conditions will result in fire or electric shocks. 

Do not use other than a specified projector. 

Do not install a projector in a way other than specified.

Doing so may cause a failing accident or a fire or electric shock.

Be sure to use the supplied parts that make up this product when installing the product.

Insufficient strength or improper installation may cause injury due to falling or a fire or electric shock.

Do not dismantle or modify this product.

Doing so may cause it to break or injury due to falling.

Do not do anything that might damage the power cord or power plug.

If the power cord is used while damaged, electric shocks, short-circuits or fire will result.

 

z

Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it 

excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. 

Ask your dealer to carry out any repairs to the power cord or power plug that might be necessary.

Do not use anything other than the provided power cord.

Failure to observe this will result in electric shocks or fire. Please note that if you do not use the provided power 

cord to ground the device on the side of the outlet, this may result in electric shocks. 

Completely insert the power plug into the wall outlet and the power connector into the projector 

terminal.

If the power plug or power connector is not completely inserted, electric shocks or overheating may result.

 

z

Do not use plugs which are damaged or wall outlets which are coming loose from the wall.

Summary of Contents for ETJPC200BU































Reviews: