background image

Panasonic Connect Co., Ltd.

Web Site : https://panasonic.net/cns/projector/

© Panasonic Connect Co., Ltd. 2022

SS0512AM2042 -PS

Printed in Japan

4)  Remove the lamp unit.

 

Use a Phillips screwdriver to turn the lamp unit 

until they turn freely, and then remove the 

lamp unit from the lamp case.

 

Hold the handles of the lamp unit and remove 

it.

 

Do not remove the screws other than the 

Lamp unit fixing screws

Lamp unit

Lamp case handle

Guide pins and guide holes

Lamp unit

Lamp unit 

handles

5)  Attach the lamp unit.

(i)  Gently push the new lamp unit into the lamp 

case. Install the new lamp unit carefully so 

that the guide pins on the lamp case are 

inserted into the guide holes on the lamp unit.

•  If the lamp unit is not installed properly, 

remove it and then gently install it again. 

Pushing it in forcibly or exerting excessive 

force may break the connector.

(ii)  Use a Phillips screwdriver to tighten the 

 

Make sure to attach the lamp unit properly.

6)  Attach the lamp case.

 

Gently push in the lamp case along the 

grooves for the lamp case attachment guide 

 

When you secure the lamp case with the 

projector installed upward in the vertical 

weight. Be sure to hold the lamp case handle 

 

If the lamp case is not installed properly, 

remove it and then gently install it again. 

Pushing it in forcibly or exerting excessive 

force may break the connector.

 

Make sure to attach the lamp case properly.

Grooves of the guide to attach the lamp case

Guides to attach the lamp case

Lamp case R

Lamp case L

Lamp case fixing screws

Lamp case handles

7)  Attach the lamp unit cover

(i)  Align the lamp unit cover to the marks of (a) 

and (b) (  and 

) to attach as shown by 

the arrow.

(ii)  Close the lamp unit cover in the direction 

of the arrow and use a Phillips screw driver 

screw (one screw).

 

Make sure to attach the lamp unit cover 

properly.

(a)

(b)

(i)

(ii)

Note

 

When you place the new lamp unit, the projector 

resets the total usage time of the lamp unit 

automatically.

 

When the lamp case is removed or attached, 

it will be caught because of the fall-prevention 

stopper. This, however, is not a problem.

Attention

 

After unpacking the lamp unit, discard the 

packaging material properly.

Summary of Contents for ET-LAD510

Page 1: ...uropean Union and countries with recycling systems This symbol on the products packaging and or accompanying documents means that used electrical and electronic products must not be mixed with general household waste For proper treatment recovery and recycling of old products please take them to applicable collection points in accordance with your national legislation By disposing of them correctl...

Page 2: ... lamp unit cover and to loosen the lamp unit cover fixing screws with the projector installed upward in the vertical direction since the lamp unit cover may open and the lamp case may drop off on its weight z This can cause severe injury or accidents When you loosen or fix the lamp case fixing screws with the projector installed upward in the vertical direction make sure to hold the lamp case hand...

Page 3: ... freely and then open the lamp unit cover slowly in the direction of the arrow described in the following figure Opening the lamp unit cover quickly may result in damage to the cover If you loosen the lamp unit cover fixing screw with the projector installed upward in the vertical direction the lamp unit cover may open on its weight and drop off the lamp unit ii Hold the lamp unit cover securely a...

Page 4: ... push in the lamp case along the grooves for the lamp case attachment guide When you secure the lamp case with the projector installed upward in the vertical weight Be sure to hold the lamp case handle If the lamp case is not installed properly remove it and then gently install it again Pushing it in forcibly or exerting excessive force may break the connector Make sure to attach the lamp case pro...

Reviews: