Panasonic DMPBDT100 - 3D BLU-RAY DISC PLAYER, Operating Instructions Manual

Page: 32 / 320

Downloaded from www.vandenborre.be
32
VQT2U34
Reference Reference
Troubleshooting guide
Before requesting service, please perform
the following steps.
The following do not indicate a problem with this unit:
≥
Regular disc rotating sounds.
≥ Image disturbance during search.
≥
Image disturbance when replacing 3D discs.
∫
Unit doesn’t respond to remote
control or front panel buttons.
Press and hold [ Í /I] on the main unit for 3 seconds.
– If still unable to turn the unit off, disconnect the AC mains
lead, wait 1 minute, then reconnect the AC mains lead.
∫
Cannot eject disc.
The unit may have a problem.
1
While the unit is off, press and hold [OK], the yellow
button and the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2
Repeatedly press [ 1 ] (right) on the remote control or
[ Í /I] on the unit until “06 FTO” is displayed on the unit’s
display.
3
Press [OK] on the remote control or [
<
OPEN/CLOSE]
on the unit.
To return to the factory preset.
¾ Select “Yes” in “Default Settings” in the Setup menu.
(
> 31)
To return all settings to the factory preset.
¾ Reset the unit as follows:
1
While the unit is off, press and hold [OK], the yellow
button and the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2
Repeatedly press [ 1 ] (right) on the remote control or
[
Í
/I] on the unit until “08 FIN” is displayed on the unit’s
display.
3
Press and hold [OK] on the remote control or [ < OPEN/
CLOSE] on the unit for at least 3 seconds.
This unit is turned off when the input for the
TV is switched.
¾
This is a normal phenomenon when using VIERA Link
(HDAVI Control 4 or later). For details please read the
operating instructions for the TV.
The remote control doesn’t work properly.
¾ The remote control and main unit are using different
codes. If “SET 1”, “SET 2” or “SET 3” is displayed when
a button is pressed on the remote control, change the
code on the remote control. (
> 31)
¾ It may be necessary to set the manufacturer code or the
remote control code again after changing the batteries
for the remote control. (
>
15)
The TV tuner mode is not displayed when
the TV is switched on.
¾ This phenomenon may occur, depending on the TV
setting, when “Quick Start” is set to “On”.
– Depending on the TV, this phenomenon may be prevented
by reconnecting the HDMI cable to a different HDMI input
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾ The ratings level returns to the factory preset.
1
While the unit is on, press and hold [OK], the yellow
button and the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2
Repeatedly press [
1
] (right) on the remote control or
[
Í
/I] on the unit until “03 VL” is displayed on the unit’s
display.
3
Press [OK] on the remote control or [ < OPEN/CLOSE]
on the unit.
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies.
(
> 14)
4
Make the following checks.
If the problem remains unresolved, consult
your dealer for instructions.
General operation
(32)
DMP-BDT100EG-VQT2U34.book 32 ページ ２０１０年６月２２日 火曜日 午前１１時０分