63
RQT8856
Ref
erence
General Issues
Operation (Continued)
Page
The remote control doesn’t work.
Coloured glass may obstruct the signal reception/transmission.
•
−
Don’t place the signal sensor in direct sunlight or in areas that may be subject
to sun exposure.
•
−
It may be necessary to set the manufacturer code again after changing the batteries.
•
53
The Child Lock function is activated.
•
53
The unit is on but cannot be
operated.
Some operations are prohibited by the disc.
•
−
The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears.
•
70
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
Press [
8
] on the main unit to switch to standby mode.
If the unit doesn’t switch to standby mode, reset the unit (
➔
61, “To restore the
unit if it freezes”).
•
−
The unit cannot be operated while performing an update. “SW-DL” appears on
the unit’s display while it is updating. Please wait until the “SW-DL” disappears.
•
52
“U88” is displayed and the disc
cannot be ejected.
The unit is carrying out the recovery process. The disc may be defective. Do
the following to eject the disc. Try another disc.
(1) Press [
8
] on the main unit to switch to standby mode.
If the unit doesn’t switch to standby mode, reset the unit (
➔
61, “To restore
the unit if it freezes”).
(2) While the unit is turned off, press and hold [
g
] and [CH
1
] on the main
unit at the same time for about 5 seconds. (Ejection may take extra time
depending on discs.)
•
−
Cannot eject a disc.
The unit is recording.
•
−
The unit may have a problem. Eject the disc as in (2) above.
•
−
Linked timer recordings with external equipment is in recording standby (“EXT-
L” on the unit’s display blinks when [
^
DVD] is pressed). Press [EXT LINK] to
cancel the recording standby.
If the Child Lock function is activated, above operation does not work. Cancel
the Child Lock function.
•
21,53
Startup is slow.
Startup takes time in the following situations:
A disc other than a DVD-RAM is inserted.
The clock is not set.
Immediately after a power failure or the AC mains lead is connected.
When the unit is connected with an HDMI cable.
When “Power Save” is set to “Off”, Startup becomes faster than when “Power Save” is “On”.
•
–
–
–
–
•
−
52
General Issues
TV Guide
Page
The TV Guide System does not
receive any data.
Check whether the clock is properly set.
•
11
If signal quality is bad (ghost images or limited reception), the TV Guide
system may not be able to receive any data.
•
−
“No Data” is displayed for some or
all stations.
Some stations are not supported by the TV Guide system.
•
−
Programme the Timer recording manually.
•
24
The TV Guide information is not
displayed properly.
There was a programme change or TV Guide information from a broadcast
station was possibly not correctly transmitted.
Check the current programme, e.g. on the Web site for the TV Guide system
provider or station provider.
•
−
The TV Guide data is not updated.
The unit must be in standby mode in order to update the data. If the unit is in EXT
LINK mode (“EXT-L” lights up in the unit’s display), then the data update may also
not work.
•
−
Make sure that the time is set correctly.
•
11
Check whether “Off” is set under “EPG Download in Standby” and change
the setting in System Update in the Setup menu.
•
52
RQT8856-B̲DTP̲070306.indb 63
RQT8856-B̲DTP̲070306.indb 63
2007/04/04 17:49:46
2007/04/04 17:49:46
