manualshive.com logo in svg

Panasonic DBS Series, Overview, Page: 5 / 31

Share
Download
Panasonic DBS Series Overview Download Page 5

Panasonic Digital Business System - Overview

April 1997

Issue 6

5

Port To Port Connections Permitted

The following port to port connections can be made.

Table 3 - Call Paths

Port To Port Loss

The following table shows the maximum port to port and associated cable loss.

Table 4 - Port To Port Loss

Relative Levels

The input and output relative levels for each port type are shown below. These values
assume zero cable loss.

Table 5 - Relative Levels

Loudness Rating

The loudness rating for each port type is given below. (PTRP -                          )

Table 6 - Loudness Rating

Call Path

Call Path

Call Path

Call Path

PAS > ITS

ITS > ITS

ITS > PAS

1AS > 1AS

PAS > 1AS

ITS > 1AS

1AS > PAS

1AS > ITS

Port > Port

Port > Port Loss

Associated Cable Loss

PAS > 1AS

1.3 dB

0.7 dB

PAS > ITS
ITS > 1AS

Port

Input (dBr)

Output (dBr)

PAS

-6

2.5

1AS

3.5

-7

ITS

PTRP > ITS

0 dB

ITS > PTRP

2.5 dB

PTRP > 1AS

1AS > PTRP

PTRP > PAS

PAS > PTRP

Summary of Contents for DBS Series
































Reviews:

No comments