3
Power Supply Wiring
• Power supply voltage : AC24 V 60 Hz 1-PH
• Voltage
fl
uctuation : ±10 % or less
• Electric power consumption : 20 W
• Be sure to use a dedicated line for power source.
Type of wiring
• Use a
fl
exible wiring of AWG #17 - AWG #14
Total Wire Length
• 99 ft. (30 m) or less
Inter-Unit Control Wiring
Type of wiring
• Use a
fl
exible wiring of AWG #20 - AWG #14
• No polarity
Total Wire Length :
3280 ft. (1000 m) or less
Number of connectable units and devices :
(
→
P.1 “Speci
fi
cations”)
Attention
• When using the unit at a location susceptible to electrical
noise, use a
fl
exible shield wiring (one side grounding).
Communication Adaptor Control Wiring
(When connecting a Communication Adaptor)
Polarity (
+
/
-
) present
Number of connectable Communication Adaptor
• up to 7 units
For the type of wiring and total wiring length,
see “Installation Instructions” supplied with the
Communication Adaptor.
External I/O Wiring
(When connecting external equipment)
Type of wiring
• Use a
fl
exible wiring of AWG #20 - AWG #14
Wire Length :
66 ft. (20 m) or less
Attention
• When using the unit at a location susceptible to electrical
noise, use a
fl
exible shield wiring (one side grounding).
LAN Cable
(When connecting to a network)
Type of wiring
• Category 5 or above straight cable
Wire Length :
328 ft. (100 m) or less
Preparations for Wiring
Basic Wiring Diagram
U1 U2
U1
U2
+
–
U1 U2
U1 U2
L
N
U1 U2
U1 U2
+
–
N
L
Power source
(AC 120 V 60 Hz)
Outdoor unit
This unit
Power trans
*3
(AC 24 V 60 Hz)
[
fi
eld supplied item]
Power supply wiring
Communication
Adaptor
Communication
Adaptor
control wiring
• Polarity
present
Inter-unit control
wiring
• No polarity
Outdoor
unit
Indoor unit
Indoor unit
1-1
Indoor unit
1-2
*3: The AC 24 V power from an energy limited Class II
power source must be provided to the equipment.
1. Turn the circuit breaker off before connecting the wiring
2. How to Attach the Ring Pressure Terminal
For power supply wiring
Process the end of each wiring, and
attach the ring pressure terminal (
fi
eld
supplied item).
For shield wiring
Process the end of the each wiring and attach the ring
pressure terminal (
fi
eld supplied item).
Remove wiring coat.
Shield mesh
Cover with the tape.
Strip
Shield mesh
Insulation tape
Attach ring pressure
terminal.
Ring pressure
terminal
3. Remove the
power switch
cover
4. Wiring
Connect the power supply wiring.
• Do not over-tighten. (The screw may be damaged.)
Connect the inter-unit control wiring.
When using the shield wiring, connect the shield part
of the shield wiring to No. 0 (FG
*4
) of the signal terminal
board (TB2).
*4: Functional Ground
• Do not over-tighten. (The screw may be damaged.)
There is no polarity.
Connect the Communication Adaptor control wiring.
Make sure the polarities (+/-) are correct.
Attention
• Read the “Installation Instructions” supplied with the
Communication Adaptor.
Connecting external equipment.
Attention
• See “Connecting to External Equipment” (P.4).
Fix the power supply wiring and other communication
wirings with the clamper (supplied) securely.
(Do not apply tensile force on the terminal connection part.)
Connect the LAN cable.
After all wiring arrangements are complete, turn
the circuit breaker on.
• Before power on, measure the voltage of the power supply
terminal board, and check it for the speci
fi
ed voltage.
Turning the power on with a voltage other than the
speci
fi
ed one may blow the fuse. If this occurs, no power
is supplied, and this unit may need to be replaced.
Strip
Ring
pressure
terminal
Screw
Screw
Power switch cover
Power-in port
Wiring
CZ-256ESMC2U̲工説北米̲冊子.indd 3
CZ-256ESMC2U̲工説北米̲冊子.indd 3
2016/08/03 16:16:50
2016/08/03 16:16:50
