Panasonic CS-YC12NKV-6 Service Manual Download Page 21 | Manualshive

Page: 21 / 36

Panasonic CS-YC12NKV-6 Service Manual Download Page 21

21

9.4 Indoor Fan Speed Control

Indoor fan speed can be set using remote control.

9.4.1

Fan Speed rotation Chart

speed

Model

Hi

Me

Lo

CS-YC12NKV-6

1080

960

800

9.4.2

Automatic Fan Speed Control

When set to Auto Fan Speed, the fan speed is adjusted between maximum and minimum setting as shown in
the table.

Shi

Hi

Me

Lo

Lo-

SLo

SSLo

Auto

o

o

o

Cooling

Manual

o

o

o

Auto

o

o

Soft Dry

Manual

o

o

Auto Fan Speed during cooling operation:-

1. At the beginning of each compressor starts operation, indoor fan speed increases gradually for deodorizing

purpose.

2. Indoor fan will rotate alternately between off and on as shown in below diagram.

*1. Fan speed will be at Hi till the compressors ceases when set temperature is reached.
*2. Fan Speed will be at Me when the compressor restarts.

Auto Fan Speed during soft Dry operation.

1. Indoor fan will rotate alternately between OFF and Lo-.
2. At the beginning of each compressor starts operation, indoor fan will increase fan speed gradually for deodorizing

purpose.

«
...
19
20
21
22
23
...
»

Summary of Contents for CS-YC12NKV-6





































Reviews:

No comments