Panasonic CS-TE12HKE Service Manual Download Page 34 | Manualshive

Page: 34 / 56

Panasonic CS-TE12HKE Service Manual Download Page 34

34

13.2. Protection Control For Cooling & Soft Dry Operation

13.2.1.

Outdoor Air Temperature Control

• The compressor operating frequency is regulated in accordance to the outdoor air temperature as shown in the diagram below.
• This control will begin 1 minute after the compressor starts.

13.2.2.

Cooling Overload Control

• Detects the Outdoor pipe temperature and carry out below restriction/limitation (Limit the compressor Operation frequency)
• The compressor stop if outdoor pipe temperature exceeds 63

q

C

• If the compressor stops 4 times in 20 minutes, Timer LED blinking (F95: outdoor high pressure rise protection)

13.2.3.

Freeze Prevention Control

1. When indoor heat exchanger temperature is lower than 0

q

C continuously for 6 minutes, compressor will stop operating.

2. Compressor will resume its operation 3 minutes after the indoor heat exchanger is higher than 13

q

C.

3. At the same time, indoor fan speed will be higher than during its normal operation.

4. If indoor heat exchanger temperature is higher than 13

q

C for 5 minutes, the fan speed will return to its normal operation.

«
...
32
33
34
35
36
...
»

Summary of Contents for CS-TE12HKE

























































Reviews:

No comments