manualshive.com logo in svg

Panasonic CS-PC36JKV, Service Manual

Share
Download
Panasonic CS-PC36JKV Service Manual Download Page 31

31

12.7. Odour Cut Control

• Odour cut operation removes the odour generated at indoor heat exchanger by using drain water come out from indoor heat

exchanger.

• Press “Odour” button at remote control to enable odour cut operation.
• Odour cut operation starts when compressor or thermostat is on.

12.8. Vertical Airflow Direction Control

Auto Control

• When the vertical airflow direction is set to Auto using the remote control, the louver swings up and down as shown in the

diagram.

• When stop operation using the remote control, the discharge vent is reset, and stop at the closing position.
• During Cooling operation or Soft Dry operation, indoor fan motor may stop to rotate at certain periods. At that condition, the

louver will stop swinging and rest at the upper limit.

Manual Control

• When the vertical airflow direction is set to Manual using the remote control, the automatic airflow is released and the airflow

direction louver move up and down in the range shown in the diagram.

• The louver can be adjusted by pressing the button to the desired louver position.
• When stop operation using the remote control, the discharge vent is reset, and stop at the closing position.

12.9. Horizontal Airflow Direction Control

• The horizontal airflow direction louvers can be adjusted manually by hand.

Thermostat & 

Compressor ON/OFF

Thermostat & Compressor ON

Thermostat & Compressor OFF

Thermostat & Compressor ON

Time

40 sec.

50sec.

-

20 sec.

160 sec.

20 sec.

40 sec.

50 sec.

-

Cooling

Off

SSLo

Normal 

Operation

SSLo

Off

SSLo

Off

SSLo

Normal 

Operation

Soft Dry

Off

SSLo

SLo

SSLo

Off

SSLo

Off

SSLo

SLo

Summary of Contents for CS-PC36JKV





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands