manualshive.com logo in svg

Panasonic CS-E7HKEW, Service Manual, Page: 57 / 94

Share
Download
Panasonic CS-E7HKEW Service Manual Download Page 57

57

13.1.9.

Low Frequency Protection Control 2

• When all the below conditions comply, the compressor frequency will change to lower frequency.

13.2. Protection Control For Cooling & Soft Dry Operation

13.2.1.

Outdoor Air Temperature Control

• The compressor operating frequency is regulated in accordance to the outdoor air temperature as shown in the diagram below.
• This control will begin 1 minute after the compressor starts.
• Compressor frequency will adjust base on outdoor air temperature.

13.2.2.

Cooling Overload Control

• Detects the Outdoor pipe temperature and carry out below restriction/limitation (Limit the compressor Operation frequency)
• The compressor stop if outdoor pipe temperature exceeds 61

q

C

• If the compressor stops 4 times in 20 minutes, Timer LED blinking (F95 indicated: outdoor high pressure rise protection)

13.2.3.

Freeze Prevention Control

1. When indoor heat exchanger temperature is lower than 0

q

C continuously for 6 minutes, compressor will stop operating.

2. Compressor will resume its operation 3 minutes after the indoor heat exchanger is higher than 13

q

C.

3. At the same time, indoor fan speed will be higher than during its normal operation.
4. If indoor heat exchanger temperature is higher than 13

q

C for 5 minutes, the fan speed will return to its normal operation.

13.2.4.

Dew Prevention Control 1

• To prevent dew formation at indoor unit discharge area.
• This control will be activated if:

- Outdoor air temperature and Indoor pipe temperature judgment by microcontroller is fulfilled.
- When Cooling or Dry mode is operated more than 20 minutes or more.

• This control stopped if:

- Compressor stopped.
- Remote control setting changed (fan speed / temperature).
- Outdoor air temperature and indoor intake temperature changed.

• Fan speed, angle of louver (vertical airflow angle) will be adjusted accordingly in this control.

- Fan speed will be increased slowly if the unit is in quiet mode but no change in normal cooling mode.
- The angle of horizontal louver will be changed as table below:

Temperature, T, for:

Cooling/Soft Dry

Heating

Indoor intake air (

q

C)

T < 15 or T   30

—

Outdoor air (

q

C)

T < 16 or T   38

T < 4 or T   24

Indoor heat exchanger (

q

C)

T < 30

T  

0

Operation Mode

Airflow Direction

Vane Angle (

q

)

1

2

3

4

5

Cooling and e-ion

Auto

22 ~ 30

Manual

22

24

26

28

30

Summary of Contents for CS-E7HKEW































































































Reviews:

No comments