![background image](http://html1.mh-extra.com/html/panasonic/bl-c1a-network-camera/bl-c1a-network-camera_getting-started_4078574003.webp)
To ensure that the most current image is
displayed, Internet Explorer should be
configured as follows. This will not have a
negative effect on normal use.
1. While viewing any website, click [Tools]
[Internet Options].
2. In the section "Temporary Internet
Files", click [Settings] and check [Every
visit to the page].
•
If a Security Warning window is displayed when installing ActiveX
Controls, click [Yes].
•
To install ActiveX Controls on Microsoft Windows XP Service Pack
2, see "Security Warning window on Microsoft Windows XP Service
Pack 2" on the next page.
• The port number must be specified at the end of the camera URL.
For example
Using port 80: http://(Cameraname).viewnetcam.com
or http://IP Address
Using any other port: http://(Cameraname).viewnetcam.com:Port Number
or http://IP Address:Port Number
• The URL for the local network access may be different from the one set up
on the previous page.
Note
•
When [Enable] was selected
at step .
•
When [Disable] was selected at
step .
Note
When "Setup completed" is displayed, click [To
Single Camera page].
To register with the "Viewnetcam.com FREE DynamicDNS
service", check [Register with Viewnetcam.com] and click
[Next>].
The Enter Network Password window is displayed.
Enter the user name and password that were set,
and click [OK].
The "Viewnetcam.com FREE DynamicDNS service"
website is displayed. Follow the displayed
instructions for registration.
When the Single Camera page is displayed,
setup is complete.
Registration with the "Viewnetcam.com
FREE DynamicDNS service"
•
If you selected [Do not register with Viewnetcam.com], skip to step
.
• If the message "Failed to configure the router's Port Forwarding by UPnP"
is displayed, your router may not support UPnP
TM
or UPnP
TM
is not enabled.
Enable your router's UPnP
TM
or set Port Forwarding manually following the
router's manual, and try Automatic Setup again. For more information
about setting up a router, refer to the Panasonic Network Camera support
website at
http://panasonic.net/pcc/ipcam/
• If the message "Failed to register with Viewnetcam.com." is displayed, con-
firm that the router is connected to the Internet.
By registering with the Viewnetcam.com FREE DynamicDNS service,
you can create a personalized web address at which your camera's live
video can always be found on the Internet. For detailed information,
access "
http://www.viewnetcam.com
".
Click [Automatic Setup (Internet Access)].
The Enter Network Password window is displayed. Enter the
user name and password that were set, and click [OK].
Select the camera on the camera list to set up the
Internet access and click [Execute].
•
This program searches for the cameras that are connected to the
router and displays their MAC Addresses, IP addresses and Port
Numbers.
If more than 20 minutes have passed since the camera was turned on, the
camera cannot be set up from the Setup Program. In this situation, restart the
camera.
When using a router that supports UPnP
TM
, check [Enable].
When using a router that does not support UPnP
TM
, check
[Disable]. Then click [Next>].
•
Check if your router supports UPnP
TM
referring to the router's manual.
•
If you select [Disable], skip to step .
Note
Camera
List window
Camera
Status
Port
No.
MAC
Address
IP
Address
• The MAC Address on the rear side (see page 5 of the Operating Instructions
on the CD-ROM.) of the camera shows which camera you select on the camera
list window.
3.
Set up Internet access to the camera.