background image

© Panasonic Corporation 2017.

 

 

 

 
 

Indoor Unit

Outdoor Unit

 

WH-SDC12H6E5
WH-SDC16H6E5

WH-UD12HE5
WH-UD16HE5

Destination

Europe

Turkey

 

WARNING 

This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the products dealt with in this service information by anyone else could result in serious injury or death. 

 

 

 

There are special components used in this equipment which are important for safety. These parts are marked by      in the Schematic
Diagrams, Circuit Board Diagrams, Exploded Views and Replacement Parts List. It is essential that these critical parts should be
replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission
of manufacturer.

IMPORTANT SAFETY NOTICE

 

 

In order to avoid frostbite, be assured of no refrigerant leakage during the installation or repairing of refrigerant circuit.

 

PRECAUTION OF LOW TEMPERATURE 

 

Summary of Contents for Aquarea WH-UD12HE5










































Reviews: