8
J
RCB connector [RCB]
The simplified remote control unit (RCB, optional
accessory) is connected to this connector.
K
External power supply input connector [DC IN]
The input of the external DC power supply is connected
to this connector. (DC 12V)
L
MIC1 selector switch [MIC1 F/R]
This is used to switch the MIC1 input signal to the front or
rear.
M
Rear MIC1 connector [MIC1]
An audio component or microphone is connected to this
connector.
N
Rear MIC2 connector [MIC2]
An audio component or microphone is connected to this
connector.
O
Tally output connector [TALLY OUT]
The R or G tally signal is output from this connector
(open collector). A DC 12 V voltage (approx. 1.0 A) can
also supplied.
P
Earphone jack [EARPHONE]
When an earphone (optional accessory) is connected to
this jack, the INCOM1 receive signal and MIC1 monitor
signal can be heard.
Q
Data trunk connector [TRUNK]
The trunk data [RS-422 x2] of the CCU is input to and
output from this connector.
R
MIC1 power selector switch
This is used to select what kind of power is to be
supplied to MIC1. (The switch is set to phantom 48 V,
AB 12 V or OFF.)
S
MIC2 power selector switch
This is used to select what kind of power is to be
supplied to MIC2. (The switch is set to phantom 48 V,
AB 12 V or OFF.)
T
Input gain selector switch
This is used to set the MIC1 input gain (in 10 dBm
increments from -20 to 60 dBm).
U
MIC2 input gain selector switch
This is used to set the MIC2 input gain (in 10 dBm
increments from -20 to 60 dBm).
V
RET selector switch [RET]
This is used as return image selector switch.
W
Optical filter selector switch [FILTER LOCAL]
This is pressed to adjust the optical filter manually.
When it is pressed again, the optical filter can be
controlled by the ROP.
X
Monitor output selector switch [MONI SEL]
This is used to select the images (Y, NAM, R, G, B]
which are to be output from the monitor output connector.
Y
ND filter selector knob
This is used to adjust the optical filter manually when
LOCAL has been selected as the filter setting.
1: CAP, 2: Through, 3: 1/4, 4: 1/16, 5: 1/64
Z
CC filter selector knob
This is used to adjust the optical filter manually when
LOCAL has been selected as the filter setting.
A: 3200K, B: 4300K, C: 6300K, D: Cross, E: DFO
[
Power save switch [CAM/VTR]
This is used to select the power supply status when VTR
recording has been temporarily stopped. It is not
effective when the CCU is connected to the camera.
\
Gain selector switch [GAIN]
This is used to select the gain for the camera images. It
is not effective when the CCU is connected to the
camera.
]
Camera output selector switch [OUTPUT]
This is used to select the video output (CAM, BAR or
TEST). It is not effective when the CCU is connected to
the camera.
^
White balance selector switch [W.BAL]
This is set when there is no time to perform the coarse
adjustment of the white balance. It is not effective when
the CCU is connected to the camera.
_
PTT switch [PTT]
This selector switch is used to set the INCOM1 MIC to
ON or OFF.
`
Assignable switch [USER SEL]
Using the setting menu, user settings can be assigned to
this switch. When the switch is pressed, the assigned
user setting mode is established; when it is pressed
again, the selected mode is released.
a
SD card connector [SD CARD]
The setup card (optional accessory) is inserted here. For
details on its operation, refer to the menu.
b
Menu switch [MENU]
When this switch is pressed, the camera’s user menu is
output; when it is pressed again, the menu screen
display is cleared.
Controls and their functions
