Panasonic AJ-PCD35E Operating Instructions Manual Download Page 12

12

Installation 

(continue)

7

Connect the AC adapter included with the 
P2 drive to the unit’s DC IN 16V socket.
Start up the P2 drive.
Check that the green light on the unit’s 
power indicator turns on and that the 
status indicators for all card slots blink 
about once per second.

For the AJ-PCD35EJ only:
Plug the power switch box supplied with 
the P2 drive into the DC IN 16V socket on 
the P2 drive, then plug the supplied AC 
adapter into the power switch box. The P2 
drive will start when you turn ON the 
switch.
Confirm that the power indicator on the P2 
drive lights green, and that the status 
indicators for each slot blink for about one 
second.

<Note>

Disconnect the AC mains plug from the 
AC mains socket when not in use.

8

Start up the personal computer.

9

Verify that the personal computer 
recognises the P2 drive.

<Notes>

z

In Windows XP, some card slots of the P2 
drive may be assigned drive names that have 
already been assigned to existing networks. 
Reassign network drive names if your 
personal computer does not display all five 
card slots.

z

Since the P2 drive does not support hot-
plugging, do not insert or remove the PCI 
Express cable with the personal computer 
power on.

z

While the P2 drive and the personal computer 
are connected, do not insert or remove the 
unit’s AC adapter when the personal computer 
is on. If the personal computer is on with the 
unit off, before turning the unit on, turn the 
personal computer off.

DC IN 16V

DC IN 12V

DC IN 16V

DC IN 12V

AC adapter

Pay attention to the items below if you are
using Mac Pro (1st Generation).

z

Insert the PCI Express board supplied into 
the slot 1 or 4 in MAC Pro (1st Generation) 
(Slot number is for using the number of lanes 
in a normal condition).

If you insert the board into the slot 2 or 3, 
change the number of slot lanes to 

a

4 or 

a

before insertion by selecting “System” 

”Library” 

>

 “CoreServices” 

”Expansion 

Slot Utility”.

z

If you use more than 

a

8 lanes of RAID 

interface card and this device in combination, 
operation speed may be limited due to the 
setting of the number of lanes.

AJ-PCD35P_E_EJ(VQT1X46-5)_E.book  12 ページ  2013年3月19日 火曜日 午前9時58分

Summary of Contents for AJ-PCD35E




















Reviews: