DSD 642
OPERATING INSTRUCTIONS
25
6
Press OK.
The DSD Status screen is displayed
7
To exit the DSD Status information screen, press EXIT to return
to the previous menu or MENU to return to the service.
CA Status
1
Repeat steps 1 to 5 of the DSD Status screen (page 23).
2
Press
?
to highlight CA Status.
3
Press OK.
The CA Status screen is displayed.
4
To exit the CA Status information screen, press EXIT to return to
the previous menu or MENU to return to the service.
TV Installation
TV Type
Typical values are PAL I, PAL G, etc. The TV type is determined by the
TV system used in the country of installation. To set the TV Type:
1
Press MENU on the RCU.
The Main Menu options list is displayed.
2
On the RCU, press
?
to highlight Advanced Options.
3
Press OK.
The Advanced Options Menu is displayed.
4
Press
?
to highlight TV Installation.
5
Press OK.
A security check screen is displayed, in which you must enter the
installation PIN (9949)
The TV Type screen is automatically displayed when the correct
PIN is entered.
6
Press OK
A TV type list is displayed in which PAL I is highlighted. Press
?
to highlight any other TV type.
7
Press OK to activate the setting and leave the screen, or EXIT to
cancel the setting.
Aspect Ratio
The Aspect Ratio allows the user to select between a normal width TV
and a wide-screen TV.
1
Repeat steps 1 to 5 for setting the TV Type (page 22).
2
Press
?
to highlight Aspect Ratio.
3
Press OK.
The Aspect Ratio screen is displayed, in which the 4:3 aspect is
highlighted.
4
Press
?
to select the 16:9 aspect ratio (4:3 is for normal TV, 16:9
for wide-screen TV).
5
Store the setting by pressing OK on the RCU.
UHF Tuning
The UHF Tuning application allows the user to select a UHF channel for
satellite viewing.
1
Repeat steps 1 to 5 for setting the TV Type (page 24).
2
Press
?
to highlight UHF Tuning.
3
Press OK. The UHF Tuning screen is displayed and the decoder
front panel display shows the current UHF channel number.
4
Press
=
or
<
to increase or decrease the channel number.
If the channel number is changed, the TV picture is lost because
the TV is not tuned to the new channel. The changed channel
number is displayed on the decoder front panel.
5
Store the setting by pressing OK on the RCU.
6
Press MENU to exit from the menu.
7
Retune the TV set to the new decoder UHF channel.
TIP
:
Pressing and holding down UHF for 5 seconds (not in menu,
Information Bar or EPG mode) also causes the UHF Tuning
screen to be displayed.
NOTE:
Pressing EXIT at any time while this screen is
displayed will return you to the service without
saving any changes made.
Scart Source
This screen allows the user to set the sources for the various SCART
connectors on the decoder.
1
Repeat steps 1 to 5 for setting the TV Type (page 24).
2
Press
?
to highlight Set Scart Source.
3
Press OK. The Set Scart Source Menu is displayed.
4
Press
>
or
?
to highlight the SCART source to be edited.
5
Press
=
or
<
to set the source of the selected SCART.
6
Store the setting by pressing OK on the RCU.
7
Press EXIT to return to the previous menu or MENU to return to
the service.
Scart Video Output
This screen allows the user to set the video output type for the various
SCART connectors on the decoder.
1
Repeat steps 1 to 5 for setting the TV Type (page 24).
2
Press
?
to highlight Scart Video Output.
3
Press OK. The Scart Video Output Menu is displayed.
4
Press
>
or
?
to highlight the SCART to be edited.
5
Press
=
or
<
to set the video output type of the selected
SCART.
6
Store the setting by pressing OK on the RCU.
7
Press EXIT to return to the previous menu or MENU to return to
the service.
Summary of Contents for DSD 642
Page 1: ......
