background image

Auxiliary equipment

Local safety standards

The user must make sure that he operates all auxiliary 

equipment in accordance with local codes, standards, 

regulations, or laws applicable to safety.

Working area

WARNING!

Auxiliary equipment may have both manual 

and automatic modes of operation. As 

equipment can move suddenly and without 

warning, do not enter the work cell of this 

equipment during automatic operation, 

and do not enter the work envelope of this 

equipment during manual operation. If you 

do, serious injury can result.

WARNING!

Make sure that power to the auxiliary 

equipment is turned OFF and locked out 

before you perform maintenance procedures 

on this equipment.

Qualification of personnel

Make sure that all personnel have manufacturer-approved 

training applicable to the auxiliary equipment.

Personal safety equipment

Make sure that operators and maintenance personnel have 

all safety equipment applicable to the auxiliary equipment. 

Examples include safety glasses, protective headgear, 

safety shoes, etc.

Unauthorized operation

Make sure that unauthorized personnel cannot gain access 

to the operation of the equipment.

Environmental compliance

RoHS

The PanaFlow™ LZ fully complies with RoHS regulations 

(Directive 2011/65/EU).

Waste Electrical and Electronic Equipment (WEEE) directive

Panametrics is an active participant in Europe’s Waste 

Electrical and Electronic Equipment (WEEE) take-back 

initiative (Directive 2012/19/EU).

The equipment that you bought has required the extraction 

and use of natural resources for its production. It may 

contain hazardous substances that could impact health 

and the environment.
In order to avoid the dissemination of those substances in 

our environment and to diminish the pressure on the natural 

resources, we encourage you to use the appropriate take-

back systems. Those systems will reuse or recycle most of 

the materials of your end life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use 

those systems.
If you need more information on the collection, reuse and 

recycling systems, please contact your local or regional 

waste administration.
Please visit 

https://www.bakerhughesds.com/health-

safetyand-environment-hse

 for take-back instructions and 

more information about this initiative.

iv

Summary of Contents for PanaFlow LZ





















Reviews: