Panametrics DewPro MMR101 User Manual Download Page 21

DewPro MMR101 User’s Manual

15

Chapter 3. Operating the MMR101

Chapter 3. Operating the MMR101

3.1

Introduction

This section gives a brief description of the MMR101 operation including powering up and displaying measurements. 
This section includes the following:

• Powering Up

• Displaying Measurements

• Measurement Accuracy

Use these instructions to properly operate the MMR101.

CAUTION!

To ensure the safe operation of this unit, you must install and operate the MMR101 as described in this 
manual. In addition, be sure to follow all applicable safety codes and regulations for installing 

electrical equipment in your area.

3.2

Powering Up

CAUTION!

Before powering up make sure that all equipment in proximity to the unit (e.g. valve, pumps, etc.) is 
functioning properly.

The MMR101 has a power supply that accepts 12 to 28 VDC (24 VDC nominal). After making electrical connections, 
including grounding, as described in the previous section, 

Installing the MR101

, connect power. Use the following 

section to display the desired data.

IMPORTANT:

The power line/connection is the main disconnect device.

3.3

Displaying Measurements

If your MMR101 is supplied with a display, you can display the desired measurements using the key located to the left 
and right of the display as shown in Figure 8, below. Units without the display, must be manually setup as described 
in <Title Font> Manually Setting the Measurement Units on page 5.

Figure 8: Display and Keys

The available measurements options are arranged in a matrix format. Each option is assigned coordinates on the 10 
by 10 matrix, specified with V (vertical), H (horizontal) and a number for each. You select the desired option by 
entering the matrix position. The matrix, on the next page, shows all the possible options. See below for an example of 
how to program the unit.

Example:

To set the dew point value to 5

o

C for 4 mA (V1 H3 on matrix):

1.

Press the V key until the display shows V1.

2.

Press the H key until the display shows H3.

3.

Use the + or - key to change the numeric value to 5.

 

Summary of Contents for DewPro MMR101






































Reviews: