background image

© Pan Acoustics GmbH   

     

Page 12 of 14       

Manual 

                                                                                                

Doc. Nr

.: 01684.V1 - 12.2022 [tr

anslation based on German v

ersion]

9. Maintenance and care

The accessory may show signs of wear over time, e.g. due to mechanical loads, corrosion or improp-

er handling. Therefore, for permanent installations, check at regular intervals for signs of wear and 

inspect the contact of the cables in the connector sockets.

When  performing  inspections,  it  is  particularly  important  to  watch  out  for  deformations,  cracks, 

notches, damage (on threads, cables and connectors) and corrosion. The power voltage on the power 

supply is also to be checked.

If  the  check  reveals  uncertainties  or  damaged  parts,  the  accessories  may  no  longer  be  used.

The operator/user is required to be familiar with country-specifi c comprehensive testing regulations 

and to apply them. 

10. Disposal

The product is to be disposed of according to existing national regulations.

Please ensure that the product cannot be re-used or used for any other purpose after disposal.

The declaration of conformity for the relevant product from the Pan Beam series can be re-

quested from Pan Acoustics.

11. EC conformity (CE mark)

12. WEEE declaration (disposal)

14. Contact address

Pan Acoustics GmbH

Schweigerstraße 13d

38302 Wolfenbüttel

Germany

Tel:  +49 (0) 5331 900 95 70

Fax:  +49 (0) 5331 900 95 79

Mail: [email protected]

DANTE

®

 is a registered trademark of Audinate Pty Ltd.

13. Copyright notice

The waste bin symbol points out that electrical and electronic components are not al-

lowed to be disposed of in household waste. This symbol is found on our products. If 

the product is to be disposed of, please consult with your dealer or distributor.

Summary of Contents for PAN NET















Reviews: