background image

COMMISSIONING 

70 

PRESET OUTLET TEMPERATURE 

The factory preset outlet temperature of the water heater is: 

 

55°C 

 
If a temperature controller is connected to the water heater, this will override the preset outlet temperature 
setting and the maximum outlet temperature will be: 
 
 

Maximum Outlet Temperature 

 

 

Kitchen controller connected 

55°C 

 

Bathroom controller only connected 

50°C 

 

 
 
It is usually not necessary to check or adjust the factory preset outlet temperature of the water heater, unless 
the customer has a particular requirement for this to be done or it is to be installed as a gas booster to a 
solar water heater. 
 

Gas Booster for a Solar Water Heater 

Where a water heater is installed as a gas booster to a solar water heater, the preset outlet temperature 
must be set at 75

C for the system to operate correctly. 

 
It will be necessary to check and if required to adjust the preset outlet temperature of the continuous flow 
water heater when: 

 

it is installed as a gas booster as part of a solar water heater installation 

 

it is an existing continuous flow water heater and a solar preheat water heater is then installed. 

 

Notes: 

 

Consideration must be given to the delivery temperature to any ablution and public areas such as a 
bathroom, ensuite or public amenities. Refer to 

“Hot Water Delivery”

 on page 44 and to 

“Schematics of 2 

Temperature Zones Using A Temperature Limiting Device”

 on page 45. 

 

The water heater, marked “THIS APPLIANCE DELIVERS WATER NOT EXCEEDING 55°C IN 
ACCORDANCE WITH AS 3498” on the front panel, 

must not

 be installed as an in-series gas booster 

water heater to a solar water heater, as water temperature greater than 55°C can be delivered from the 
water heater contravening its compliance to AS 3498. 

 

TO CHECK OR ADJUST THE PRESET OUTLET TEMPERATURE 

The temperature setting will be displayed by a series of flashes from the red LED, with a three (3) second 
pause between each series of flashes. The temperature settings and series of flashes are: 
 
 

Preset Temperature Settings 

Flashes 

 

 

Minimum temperature setting 

1 flash 

43°C 

 

Mid temperature setting 

2 flashes 

55°C 

 

Maximum temperature setting 

3 flashes 

75°C 

 

 
 

Summary of Contents for Eternity











































































Reviews: