Pallas Condor, Operating Manual

Page: 14 / 76

Join our mission.
Make water count.
14
ENG
LIS
H
6.2. BASIC PROGRAMMING
Caution: The programming has to be
done only by the installer for the setting
of the valve parameters. The modification
of one of these parameters could prevent
the good functioning of the device.
To enter the programming mode, the
valve has to be in service. While in
program mode, the valve will continue
to operate normally monitoring all
information. The programming is
stored in permanent memory with or
without line or battery backup power.
To enter the programming mode,
press simultaneously and
for 5 seconds.
Press on the button in order to
jump to the next stage. Use the
and buttons in order to modify
the displayed values.
Note: You must pass through all
the programming steps and come
back in service position to save the
modifications that have been done
during the programming mode.
After 5 minutes without any button
pressed, the unit returns to normal
operation without saving.
6.2.1 Day of override - DO
Determine the maximum number
of days of operation without
regeneration
• Press and
simultaneously
for 5 seconds to
enter the menus sequence.
• Select the number of days of
Override with and
• Press to validate the selection
and advance to the next parameter.
6.2.2 Regeneration time - RT
• Adjust the
regeneration
time with
and
• Press to validate the selection
and advance to the next parameter.
User Guide Fleck 9100-SXT
6 / 36 Ref. MKT-UG-008 / C - 14.11.2019
3.3. Description and components location
3.4. By-passing
If the system is equipped with a bypass and if a problem occurs, turn the valves to bypass the system as shown in the picture
below.
4 . Programming
Note:
The controller must be plugged to be programmed.

After 5 minutes without any button pressed, the unit returns to normal operation without saving.
4.1. Basic programming
Note:
Menus are displayed in a defined and incremental order.

Day of Override
Note:
Determine the maximum number of days of operation without regeneration.
Regeneration time
Note:
Determine the time of regeneration.
A
Press and simultaneously for 5 seconds to enter the menus sequence.
B
Select the number of days of Override with and .
C
Press to validate the selection and advance to the next parameter.
D
Adjust the regeneration time with and .
E
Press to validate the selection and advance to the next parameter.
Outlet
Display
Inlet
Meter
Brine
Drain
Down button
Up button
Regeneration button
Mixing device
In Bypass
Out Out In In
Softening
System
Softening
System
Normal
operation
User Guide Fleck 9100-SXT
6 / 36 Ref. MKT-UG-008 / C - 14.11.2019
3.3. Description and components location
3.4. By-passing
If the system is equipped with a bypass and if a problem occurs, turn the valves to bypass the system as shown in the picture
below.
4 . Programming
Note:
The controller must be plugged to be programmed.

After 5 minutes without any button pressed, the unit returns to normal operation without saving.
4.1. Basic programming
Note:
Menus are displayed in a defined and incremental order.

Day of Override
Note:
Determine the maximum number of days of operation without regeneration.
Regeneration time
Note:
Determine the time of regeneration.
A
Press and simultaneously for 5 seconds to enter the menus sequence.
B
Select the number of days of Override with and .
C
Press to validate the selection and advance to the next parameter.
D
Adjust the regeneration time with and .
E
Press to validate the selection and advance to the next parameter.
Outlet
Display
Inlet
Meter
Brine
Drain
Down button
Up button
Regeneration button
Mixing device
In Bypass
Out Out In In
Softening
System
Softening
System
Normal
operation