background image

GENERAL SAFETY PRECAUTIONS

WARNING!  PROTECT AGAINST FLYING DEBRIS

Always wear proper safety glasses, goggles, or a face shield when driving pins in or 

out, or when any operation causes dust, flying debris, or any other hazardous mate

-

rial.

WARNING!  LOWER OR SUPPORT RAISED EQUIPMENT

Do not work under raised booms without supporting them. Do not use support mate-

rial made of concrete blocks, logs, buckets, barrels, or any other material that could 

suddenly collapse or shift positions. Make sure support material is solid, not de-

cayed, warped, twisted, or tapered. Lower booms to ground level or on blocks. Lower 

booms and attachments to the ground before leaving the cab or operator’s station.

WARNING!  USE CARE WITH HYDRAULIC FLUID PRESSURE

Hydraulic fluid under pressure can penetrate the skin and cause serious injury or 

death. Hydraulic leaks under pressure may not be visible. Before connecting or dis-

connecting hydraulic hoses, read your prime mover’s operator’s manual for detailed 

instructions on connecting and disconnecting hydraulic hoses or fittings.

  Keep unprotected body parts, such as face, eyes, and arms as far away as 

possible from a suspected leak. Flesh injected with hydraulic fluid may develop 

gangrene or other permanent disabilities.

• 

If injured by injected fluid, see a doctor at once. If your doctor is not familiar with 

this type of injury, ask him to research it immediately to determine proper treat-

ment.

• 

Wear safety glasses, protective clothing, and use a piece of cardboard or wood 

when searching for hydraulic leaks. 

DO NOT USE YOUR HANDS! 

  SEE ILLUSTRATION.

CARDBOARD

HYDRAULIC HOSE

OR FITTING

MAGNIFYING GLASS

10339     8-16-05

6

75595

Summary of Contents for Bradco VRS48












































Reviews: